Tutgum Bacterinol

Tutgum Bacterinol

Antibacterial Primer and top coat paint Kills and prevent mould and fungus, muzzle moisture.  Superior effectiveness.

A unique advanced Single component primer and top coat paint that is based on unique solvent acrylic copolymers thate eliminate and prevent development of fungus and mould in humid closed and un ventilated places, prevent typical putrefaction and smells. The paint is strong durable, thick, used as a primer and a top coat all in one layer application creating a smooth and elegant finish.

 

Characters:

  • Eliminates and preventing putrefaction, fungus and mould
  • Prevent bad smells
  • Excellent moisture preventive, Allows
  • Easy to
  • Very washable in water and soap.
  • Resistance to extreme
  • Excellent adhesive to

 

Applications:

  • Humid rooms- Bathroom, Toilets, Shower-room.
  • Shelters, Bunkers, Wine basement

 

QuaHties:

Industrial and professional use only. High build, applicable in one thick layer. Provides long lasting fungus prevention. Used as a decorative final layer.

Fast drying, can be repainted within an hour. Primer and a top coat all in one paint.

Has an excellent connection between different layers. Durable in heat and extreme humidity conditions.

Suitable in chemical conditions.

A 400 micron layer is applicable for extreme demands. Hard, scratch durable and shock resistant.

 

Technical specifications:

Theoretical cover area: 15-20 sqm per liter.

Cover area at the recommend layer width: 8 sqm per liter. Recommended layer width:  125 microns.

Number of recommended layers: .1-2 Flexibility: 1 mm (SHEEN)

Density: 1.1-1.4 gmcm3

Viscosity: 2-2.5 parsec (HAAKE) Rigidity: over 3 Dg (Ericson)

 

 

 

 

 

Contains:

Copolymer-acrylic resins. Special fungecides.

Preservatives and chemical purification

UV ray endurance additives.

Pigments, solvents, fillers and additives.

 

Shade:

White and a various number of colors.

 

Gloss:

Matte.

 

Touch-dryness:

20-40 minutes.(avoid overspraying)

If dust is formed while spraying add a retarder .

 

Drying time period betweien layer application:

1-4 hours.  Final:  2-6 hours.

 

Application  methods:

Brush, spray, roll.

 

Dilution:

Brushroll: 5% – 10% D-18 thinner or mineral turpentine. For slower drying and creating a surface without any brushing marks use the D-32 thinner.

Spraying: 15% – 20% D-18 thinner 3-4 atm.

Airless: ,5% 4-5 atm at diza 0.015.

 

Surface preparations:

+Mechanical removal of mould and fungus with sandpaper/sanding machine.

+Moisture areas must be cleaned with “Fungus Cleaner” and after it must be washed.

+cracks must be filled with “Denberschpachtel”.

+The surface must be dry and clean of dust and dirt before first layer implement.

+Oily/Greasy walls must be wash with Dagrizer Z until receiving dry from oils.

 

* Strict supervision is required while preparing the surface according to the instructions, which is the costumers complete responsibility. If the instructions will not be completely fulfilled the paint will peel.

Packaging:

0.5 liter, 1 liter, 2.5 liter, 5 liters, 18 liters.

 

Storage:

In a shaded and cool place at room temperature.

 

Shelf life span:

12 months in its original package.

 

 

 

 

Equipment cleansing:

Use D-18 or mineral turpentine.

 

Safety precautions:

Not eatable, keep from the reach of children.

Flammable, keep distant from heated areas, fires, flames, and sparks Wear protective glasses, gloves and suits.

Check that there is enough air while applying.

In case of an injury immediately get doctors assistance.

 

Warnings:

Dant mix with other substances that are not recommended by us.

 

Quality control:

ISO 9001-2000

In our factorys laboratories under these standards.

 

Safety precautions:

Not eatable, keep from the reach of children.

Flammable, keep distant from heated areas, fires, flames, and sparks. Prohibit smoking in the work area.

Check that there is enough air while applying. In case there is not enough air, uses ventilation

according to the ventilation table.

Wear protective glasses, gloves and suits.

Avoid direct contact with the paint and thinner from the eyes and skin. In case of contact, immediately wash thoroughly with water.

In case of an injury immediately get doctors assistance. Read the safety instructions on the labels.

 

Warnings:

Dant mix with substances and materials that were not recommended by us. Dant apply if the temperature is under +7°C.

Dant apply if the humidity is over .80%

When applying wit Airless, do not aim it at anybody a direct hit could be fatal at pressures between 150 and 300 atm.

Read thoroughly the technical data of the product listed in this section, confirm that everything is understood completely, for clarification contact our tech. department.

All information that is listed in this content is a recommendation only and do not apply in a court oflaw, the costumer must confirm that this product is compatible with his equipment and needs. The information listed in this section is according to laboratory environment which the substances were tested. At a 25°C room temp and 65% humidity.

The recommendations listed do not hold any responsibility for this product.

Theoretical and actual coverage are different concepts, the actual coverage is affected by the required width of the layers, required number of layers, painting conditions and the amount of paint absorbed in the air before touching the surface.

The information listed in this section is based on experience and accumulating data, which

has Denber inc., the right to change the information listed at any time without any note in advance. Paints that have been in stagnation could have their qualities change by up to .20%

 

 

 

 

 

Clarifications:

Storage room temperature 15°C to 25°C.

Over Spray: an effect that happens when spraying, a type of dust is created from the dryness of gases in the air and the paint particles fall dry on the surface. This effect is created by over pressure and heat, the pressure should be lowered; most sprayers have a lever to level the amount of

pressure, lower the pressure to minimum. It is also possible to spray with low pressure while getting closer to the surface.

Another possibility is to increase the amount of thinner in the mixture therefore moistening the gases in the air which would cause the paint particles to fall wet on the surface. This is common

especially when painting in open hot areas.

An additional recommended possibility in order to avoid this effect is to add retarder to the mixture that immediately increases the duration period before the paint dries up enabling it to reach the surface wet, creating an even painted smooth layer.

Pot Life : The amount of work time possible with the two substance mixture (epoxy , polyurethane) in the time of mixing A +B components of the paint , without spoiling the qualities of the paint and disqualifying the paint from usage. Some paints life spans can be increased by freezing the mixture. Spray: It is possible to spray with a sprayer that has a container holding the paint that sprays it with air pressure.

Airless: a device that puts pressure an the paint with a piston that compresses the air that creates powerful pressures that can reach >100 atm.. Dont aim the spray of paint at anyone.

Surface preparations: the levels of cleanness are determined by international standards. Cleansing sand and surface preparations are critical in order to get optimal results of adhesion of paint on the surface. These standards are equally compared to the standards of the Swiss SA, the German-DIN, the U.S SSPC SP for each standard on any level there are indicators that are for purchase in order visually compare in the field between the cleansing of the surface and the indicator.

 

Quality inspection:

Before painting large surfaces it is vital to first apply on a small surface and certify that the paint is compatible and meet the level of satisfactory.

Laboratory testing was according to the standards institution specifications.

This “Data sheet” given as an noncommittal information , the product above recommended for proffesional painting specialists. The information is not substitute to guidance.