Tutgum Denrel Clear

TutGum Denrel acrylic clear

Fast drying strong acrylic top coat protective lacquer 

 

Acrylic lacquer top coat glossy, fast drying, UV resistant, for coating top clear layer over reflective (fluorescent) paints and light emitting paints (that glow at night and in darkness) protection from sun fading accelerated, strong and protective coatings and decorative. A final top coat protective for Denrel system.

Properties:

  • Ready for use.
  • Protects againstacceleratedfadinglight sensitivecolorssuch aslight emitting and light reflecting (fluorescent).
  • Flexibleand strong,decorative
  • Excellentadhesioncapacity.
  • Easy to applyby brush andspraying.
  • Dries quickly.
  • Resistance toscratches.
  • UVresistant.

Applications:

  • Protection coat on light sensitive paints like fluorescent light reflective and light emitting paints that glows at darkness.
  • Paintingof walls, doors, columns, products Plastic/wood /metal, warning signs anddirections.
  • A generalpaintingas a protective layerfilm from scratches, for any purposeincludingvarious accessories, and vehicles.

Technical specifications:

  • Consumption: 100-200 gr/m2
  • Coverage: 1 liter to 5-10 sqm.
  • Solids: 40% (standard 785 part 17)
  • Flexibility: 1 mm (Sheen) (standard 935 part 307)
  • Grinding: < 50 micron (standard 785 part 15 < 60 micron)
  • Density: 9-1.1 gm/cm3
  • Resistance to immersion in water: no bubbles, no softness, no adhesion changes (standard 935 part 312)
  • Bleeding stability: not less than level 6 according ASTM D-868 and ASTM D-969
  • Resistance to fuels and solvents: stable according ASTM D-2792-93
  • Viscosity: 5-1.5 Pa.sec (Haake)
  • Hardness: > 10 Dg (Erichsen)
  • Erosion: 120 micro film – 1250 cycle (BYK Gardner), ASTM D4060 200 mic. dry film – loos 2 grams weight to 500 cycles (the standard allows 5 grams loss)
  • Strength to pilling : > 5 kg/cm2
  • Resistance to heat 70OC: with no changes in properties or deformation.
  • Number of recommended layers: 2
  • UV resistance: 5 years, accelerated durability in exposure to sun.

Contains:

  • acrylic resin.
  • Special flexibility
  • Wetting agents.
  • Solvents and additives.

Colors:

Gloss:

  • Glossy (standard 935 part 309).

Touch-dry time:

  • 10-30 (avoid over spraying)

Drying time period between layer application:

  • 5 hour. Final:  3 hours.

Application methods:

  • Brush, spray,

Dilution:

  • Brush/roller: 5% – 10% D-32 thinner.
  • Spraying: 10% – 30% D-32 thinner pressure 3-4
  • Airless: 0-5% thinner D-32. Pressure 5-6 nozzle 0.015”-
  • If the lid left open and the paint become thickly, a thinner D-21 can be add to dilute the paint before painting.

Surface preparations:

  • Thoroughly clean any dirt’ dust’ grease
  • Paint over mid. layer needs the protection.

Packaging:

  • 1 liter, 5 liter, 5 liters, 18 liters.

Storage:

  • In a shaded and cool place at room temperature with proper ventilation.
  • Keep lids tightly sealed.

Shelf life span:

  • 12 months in its original

Equipment cleansing:

  • Use D-21.

Quality control:

  • In factory laboratories according to specifications.
  • COA and COC certificate.
  • ISO 9001-2008

Safety precautions:

  • Inedible, keep away from the reach of children.
  • Flammable – keep distant from heated areas, fires, flames, and sparks, Prohibit smoking in working area.
  • While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
  • Wear protective glasses, gloves and suits.
  • Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
  • In case of an injury immediately get doctors assistance.
  • Read the safety instructions on the labels.
  • See M.S.D.S

Warnings:

  • Don’t mix the product with materials which were not recommended by us.
  • Don’t apply if the temperature is under +7°C.
  • Don’t apply if humidity is over 80%
  • When applying with Airless, do not aim it at anybody a direct hit could be fatal at pressures over 150 atm.
  • Read thoroughly the technical data of the product listed in this section; confirm that everything is understood completely, for clarification contacts our tech. department.
  • All information that is listed in this content is a recommendation merely and cannot be applied in the court of law.
  • The costumer must test & check that this product is compatible with his equipment and needs.
  • The information listed in this section is according to the laboratory conditions (temperature, humidity etc.) which the products were tested.
  • The recommendations listed do not hold any responsibility for this product.
  • Theoretical and actual coverage area are different concepts, the actual coverage is affected by the required thickness of the layers, required number of layers, painting conditions including the amount of paint which spread in the air before touching the surface.
  • The information listed in this section is based on experience and accumulating data, Denber inc., has the right to change the information listed at any time.
  • Paints that have been in stagnation or exposed to air more than needed could have their qualities changed.

Clarifications:

  • Storage room temperature 15°C to 25°C.
  • Over Spray: An effect which occurs in the spraying of paints application. A type of “dust” is created by dry gases of the air, which causing the paint particles to fall dry on the surface (hereafter the “effect”). The impact of this “effect” becomes stronger due to over pressure and heat, (most sprayers have a lever to control the pressure) To avoid the negative impact 0f the “effect”, the pressure of the spraying should be lowered to the necessary minimum!. Another possibility is to increase the amount of the thinner in the mixture which would cause the paint particles to fall wetter on the surface.

An additional recommended possibility, to avoid this “effect”, is to add a retarder to the mixture which increases the duration period of the painting application , avoiding the paint to  dry up, and enabling it to reach the surface wetter, Thus a better painted smooth  layer is formed.

  • Pot Life: The working time which is possible to paint a mixture of two components, A+B (or more) without spoiling the qualities of the paint or disqualifying the paint as “out of use”.
  • Spray: It is possible to spray with a sprayer that has a container holding the paint that sprays it with air pressure.
  • Airless: a device with a piston which compresses the air for spraying paints. The pressure might be high (over 100atm.) Don’t aim it at anyone
  • Surface preparations: the level of cleanness is determined by international standards. Surface preparations, including cleansing sand blasting, is important & critical factor in achieving an optimal result for painting adhesion on a certain surface. These standards are equally compared to the standards of the Swiss SA, the German-Din the U.S SSPC SP For each standard in any level there are indicators, for sale, in order to make visual comparison between the cleansing of the surface and the indicator.

Quality inspection:

  • Prior to the painting on large surfaces it is important to test the product on a small area, to be sure that the paint is compatible with the level of satisfactory.
  • Laboratory testing was made according to the standards institution specifications.
  • This “Data sheet” given as noncommittal information, the product above recommended for professional painting specialists. This information is not a substitute to personal guidance.
  • You must read the MSDS safety instructions before you start working with the product.