Epoxyden fluorescent light reflective paint

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

LIGHT REFLECTANTTWO COMPONENT MID. COAT ON WHITE PRIMER AND TOP LACQUER DENBERGLOSS CLEAR COAT

Epoxyden fluorescent light reflective paint. www.denber-paints.co.il

Epoxyden fluorescent light reflective paint. www.denber-paints.co.il

Features:

  • A paint with mechanical strength and a high adhesion to the epoxyden primer white.
  • In 8 spectacular fluorescent shades.
  • Creates a stable reflective color layer.
  • Easy to apply and repaint. Dry quickly.
  • Durable in water and industrial contaminated water.
  • Resistant to fuels and oils including to jet fuel and detergents.
  • Scratching and heating resistant.
  • Suitable for painting escape bars and directional and careful signage.
  • Coats the part painted in a thin, uniform and decorative layer.
  • Easy to wash.
  • Mechanical intensity and excellent durability in light load erosion.
  • Resistant to momentary heat of up to 200 degrees and longer heat up to 150 degrees.
  • Easy to fix at a low cost.
  • Ready to repaint the same day after 12 hours.
  • High coverage area.
  • High electrical insulation.

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Uses:

  • For internal uses without direct sun exposure.
  • Warning and directional signs.
  • Directional and referral strips for emergency escape.
  • Marking and covering and directing traffic on roads and forklifting in factory areas.
  • Marking traffic lines for transport in factories.
  • To mark limits of production areas and hazardous equipment movement.
  • Marking the signs for transportation vehicles.
  • Mark signage and highlight it.

Technical data:

  • coverage – 1 liter per 10-8 sqm. in a layer of 50 minimum dry microns.
  • Flexibility – 1 mm (sheen)
  • Density – Part 1.1-1.20 gm\cm3, Part B 0.85-0.95 gm\cm3 (ASTM D1475)
  • Viscosity – Part A About 70 Krebs Part B Approximately 25 Krebs (+10%)
  • Stiffness – >10 Dg (Ericsson)
  • Flashpoint : Part A – 27 Degrees Celsius, Part 2 – 166 degrees.
  • Solid amount – Part A weighing 68%, Part B of 52% (ASTM-D-2369)
  • abrasion – 120 microns – 2560 cycles (Gardner) ASTM
  • recommended layer thickness – 125 microns wet. 50 dry microns (minimum values)
  • Several layers recommended – 2 -1
  • hard drying time – 4 hours.
  • Pot Life (working time from the moment of mixing A with B) – 4 hours.
  • Mixing ratio A:B – 2.5:1 in volume.
  • Waiting time after mixing and before starting painting: 10 minutes and stir again with mechanical mixer.

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Contains:

  • Resin epoxy
  • Fillers.
  • fluorescent pigments.
  • Polyamid hardener
  • Solvants.
  • Additives.

Shade:

  • 8 shades by catalog: red, yellow, green, blue, orange, pink, white, lemon.

Gloss:

  • Glossy, silk, matte 10-30% (ASTM D 523)

Drying to the touch:

  • 12 minutes per layer 100 microns wet. (Due to the rapid drying avoid over spray)
  • If “dust” is created during spraying, stop painting and remove with thinner the defective color and repaint, add a retrader (drying inhibitor) and reduce air pressure to the sprayer to prevent the phenomenon. If the phenomenon does not disappear, stop painting and painting again at a lower environmental temperature.

Drying between layers:

  • 12 hours . Final:24 hours.

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Application methods:

  • Brush, roller, spraying.
  • spray – it is recommended to spray with entry pressure up to 4 atm.
  • Airles – Dilution 0-5% nozzle “0.021

Dilution:

  • Thinner 4/100 D. (suitable for MIL-T-81771 Type II)
  • 10-25% in volume according to the need for brushing/roller. If the film appearance is “orange peel”, thinner can be increased to 35%.
  • Spray gun – 10-25%
  • Airles –0-5%

Preparation of surface:

  • Thorough cleaning dust, fat, dirt and loose paint.
  • Old paint – rubbing with glass paper and removing grains: blowing with air pressure and cleaning with a cloth dipped in a suitable thinner.
  • Aluminum and aviation aluminum alloys – treatment for the preparation by burning and passivation area according to the standards: MIL-C-5541 MIL-C-81706
  • Very large elements – removal of paint with approved gradients and rinsing with water to neutralize. Polish/spray Soft balls for roughness and thorough cleaning. Thorough rinse and drying.

Primer paint:

  • Epoxyden primer white anticorrosive for iron metal.
  • Epoxyden strontium chromat for aluminum and on it a layer of white Epoxyden primer.
  • concrete – Epoxyden Floor White Primer.

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Instruction for use:

  • Carefully open parts A and B and mix separately well.
  • Pour both parts a required amount in the appropriate ratio and mix well with a mechanical mixer (recommended by air pressure for safety reasons) for a uniform mixture.
  • Wait 10 minutes and stir again while adding a thinner as required.
  • Floors – with roller spread a uniform layer, it is possible after drying another layer. Harden 7 days before full use.
  • Pour into paint equipment and spray a thin, uniform layer for at least 50 microns of dry thickness. If necessary if the layer is uneven or the part is not fully painted, wait about 4 hours (up to 12 hours if it has not completely dried up otherwise a collapsed layer will be obtained) and spray another layer.
  • Enter a clean, opaque drying room and temp controller for 12 hours before painting the top layer.
  • Wash well painted equipment at the end of the job.

Top color:

  • Denbergllos Clear for UV protection , the paint is very sensitive to sunlight and without the denbergloss protection it will fade quickly.

Life after mixing into blend A + B of 5 liters:

  • Temperature 15oC – 10 hours
  • at Temperature 20oC – 8 hours
  • at Temperature 25oC – 6 hours
  • at Temperature  30oC – 5 hours
  • at Temperature 35oC – 4 hours

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Ventilation:

  • Required air for ventilation 1 liter white epoxyden primer blend:
  • for obtaining 10% of LEL = 65M3
  • to achieve the TLV = 990 M3

Packaging:

  • 3.4+1.6 = 5 liters.

Storage:

  • In a cool, shady place at room temperature.
  • Keep lids tightly closed.

Shelf life:

  • 12 months in the original packaging.

Tool cleaning:

  • Thinner 4/100-D immediately after painting.

Safety:

  • Not edible, out of reach of children.
  • Flammable, away from heats, fire and gygs.
  • Ensure proper ventilation during implementation.
  • If there is a lack of oxygen, take care of forced ventilation or masks attached to an oxygen source. (See ventilation data above)
  • Wear goggles, solidarity-resistant gloves, protective clothing, mask suitable for filtering thinner fumes.
  • Avoid contact with the skin and eyes that cause irritation and dryness, in case of injury – seek medical attention immediately.
  • Be sure to read carefully and implement the safety instructions, be sure to undergo refresher training with a safety officer/supervisor once a month.

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades

Caution:

  • Do not mix with materials not recommended by us.
  • Avoid contact with the skin and eyes, causing dryness and irritation of the skin.
  • In contact, rinse with plenty of running water and seek medical attention.

uality control:

  • In our factory laboratories in accordance with specifications.
  • ISO 9001-2015

Please note:

  • This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Consultant Names\Guides

Epoxyden fluorescent light reflective paint

Glowing paint in 8 shades