Siliciton 960°C High Temperature paint  

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC

A high temp. silicate paint. Up to 960°C high temperature Silicate paint for direct application to iron and steel. Special water-soluble paint based on filtered inorganic materials withstanding temperatures up to 960°C, offering decorative and anticorrosive protection and cathodic protection to iron (when adding Zinc).

Siliciton 960°C High Temperature paint. www.denber-paints.co.il  

Siliciton 960°C High Temperature paint. www.denber-paints.co.il

The paint repels heat from metals and when directly applied on iron, after heating it dries turning into an inorganic silicate-like coating similar to glass. It is important to thoroughly remove grease from iron with decrease MC before painting.

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC

Properties:

    • Decorative.
    • Sticking strongly to iron metals.
    • Offering cathodic protection to iron when painted in a shade of gray (primer plus Zinc).
    • Painted in anticorrosive shades of green/black, it prevents rust from developing.
    • In silvery shade it induces heat reflection on May be painted onto light rust.
    • It withstands high temperatures, protecting the painted Acid environment withstanding.
    • Easy to apply.

Applications:

    • Painting of iron cupboards.
    • Painting of steam boilers,
    • and Painting steam and heat transporting piping (SILICITON+Zinc to paint interior piping).
    • For painting of taps and steam traps.
    • For painting cracking installations, dryers, toasting -installations and ovens.
    • SILICION+ Zinc is suitable for painting drinking water reservoirs.

Technical Data:

  • Theoretically surface covering – 1 liter/8- 15m2
  • Recommended layer thickness 25-40 microns (wet: 40-60 microns).
    • Recommended number of layers – 2
    • Density 1.15-2.4 gm/cm3
    • Flexibility 3 mm (SHEEN).
    • Hardening 3 Dg (Erickson).
    • Grinding 30 microns.
    • Viscosity 0.7-3.0 Pasec.
    • About 70% solids.
    • PH level .13-14

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC

Contents:

  • Silicates.
  • Pigments.
  • Additives.

Shades:

  • Aluminum silver/black/green for 960°C (white for 200°C, red­ brown for 600°C.)
  • Transparent solely for interior application (keep away from contact with water) up to 960°C.
  • Gray dual compound with Zinc powder, to solely be mixed before painting for cathodic protection at 960°C.

Sheen:

  • Matte

Dry to the touch:

  • 15-30 minutes.

Drying between layers:

  • Between 40 minutes up to 2 hours. Final 4-8 hours.

Application Methods:

  • Brushing, rolling, spraying.

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC

Thinning:

  • 0-15% water, it is recommended not to thin at all.

Surface preparation:

  • The surface to be painted should be cleaned of any dirt or loose Any grease that may prevent complete adhesion of SILICITON to the metal should be carefully removed.
  • Surface needs to be brushed with metal brush to remove all coarse rust.
  • If possible it is recommended to perform light sand cleaning or chemical removing of rust and grease.

Application:

  • Carry out surface preparation as required,
  • Carefully open the container and mix very well.
  • When using SILICITON+Zinc mix well both ingredients to obtain a uniform gray solution.
  • For brushing/rolling apply one thin layer and after 1 h another one.
  • For spraying it is recommended not to thin at all and to spray 2 thin layers at 40 minutes to 2 hours interval.
  • Should it be hard to spray due to spraying equipment or low air pressure and high viscosity, it is possible to use water to dilute.

Packaging:

  • 1 liter, 2.5 liter, 5 liter, 18 liter, 200 liter.

Storage:

  • At room temperature in protected area with appropriate ventilation.
  • Keep lids tightly sealed.

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC

Shelf Life:

  • 6 months in original packaging, 12 months in export packing.

Tool Cleansing:

  • Under running water immediately after using.

Quality control:

  • In factory laboratories according to specifications.
  • COA and COC certificate.
  • ISO 9001-2015

Safety precautions:

  • Inedible, keep away from the reach of children.
  • Wear protective glasses, gloves and suits.
  • Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
  • In case of an injury immediately get doctors assistance.
  • Read the safety instructions on the labels.
  • See M.S.D.S

Quality inspection:

  • Prior to the painting on large surfaces it is important to test the product on a small area, to be sure that the paint is compatible with the level of satisfactory.
  • Laboratory testing was made according to the standards institution specifications.
  • This “Data sheet” given as noncommittal information, the product above recommended for professional painting specialists. This information is not a substitute to personal guidance.
  • You must read the MSDS safety instructions before you start working with the product.

Siliciton 960°C High Temperature paint  

Based on Silicate for high temperature up to 960OC