Denberust Phenolic HD Middle layer. Denber paints and coatings

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Intermediate coating for enhancing sustainability of phenol system in chemical environments.

Anti corrosive synthetic phenolic Mid. layer paint for ferrous metals, which prevents chemical attack of the metal and rapid rust, is suitable for the fundamental painting of the metal against rust, and which prevents the development of rust resulting from contact with various acids, salts, corrosive chemicals and an alkali environment. Based on a special synthetic phenolic resin that coats the steel and prevents acid vapor from passing to the surface and the beginning of the accelerated rusting process that immediately takes place with direct contact or in an atmosphere of acids. Used as a foundation for upper Phenolic HD paint, 3309

Denberust Phenolic HD Primer. www.denber-paints.co.il

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Features:

Synthetic phenolic easy application.
Anti corrosive and prevents rust, mainly the one that is quickly generated in the area of corrosive atmosphere with acids.
Excellent adhesion capacity for ferrous infrastructure.
Allows for the preservation and protection of the metal in an acidic area from the rapid and hard rat that destroys the metal.
Easy to apply with brush, splash, roller.
Drying up quickly.
Resistant to many repeated rinses. .

Uses:

Second anticorrosive layer for protecting ferrous metals from rust in an acidic atmosphere or in contact with acids.
Black iron base paint in chemistry factories for painting steel constructions of the structure, metal coating, arrests, chemical storage boilers (for external painting)
For painting on acid spatter areas in a continuous process for immediate prevention of rust development.
For painting equipment, machinery, transport systems in and near the port.
Painting fuel pipes, oils, steam, chemicals, etc.

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Technical data:

Theoretical coverage area – 1 liter per 15 sqm
effective consumption – 200 g per square meter.
Solid% – approximately 50% (T.I.785 Part 17).
Color pigment content – 65% (TA 785 Part 19)
Flexibility – 1 mm (sheen) meets the examination of Israeli standard 935 section 307.
Grinding – up to 50 microns (Israel standard 785 Part 15 – up to 60 mic.)
Density – 1.2-1.4 gm\cm3
viscosity – at room temperature. paint: 1.5-2.sec Pa.sec (HAAKE) 78-92 Krebs in 200 rounds per minute after manual mixing of 2 minutes (T.I.935 Section 302), after diluting 10% in the thinner – 65 Krebs. After 10 days it is stored at 42ºC – the juxtaposition will increase to 5 krebs.
Rigidity – 10 Dg (Ericsson)
Abrasion – 120 microns – 1250 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 g per 500 cycles (device – up to 2.5 g of authorized loss)
heat resistance up to 70°C unchanged in features and deformation.
Recommended layer thickness –250-200 microns wet.
Number of layers recommended for element –1-2

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

contains:

Fast dry phenolic synthetic resin.
Red iron oxide.
Fillers. Pigments.
Special flexibility materials.
Depth penetration materials.
Solvents, additives.
Phosphate zinc.
Driers.

Color:

Grey.

Gloss:

Matte up to 7% (T.I.935 Section 309).

Drying to the touch:

30 minutes. Drying time on the wheel – (T.I.935 Section 304 Repair No. 2) – up to 45 minutes

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Drying between layers:

8-24 hours. Final : 16-24 hours

Application methods:

mix lightly, thin as needed and spread or spray .

Dilution:

The color is ready to use without dilution. If thick, dilute slightly with a D-18 thinner or D-32 for brush applied.
If left open, add a 21 -D thinner and mix well until you get a easy-to-use blend.

Surface Preparation:

thorough cleaning dust, fat, dirt, it is recommended to rinse with degreaser Z or M to remove fats if any, to ensure cleanliness of the area before painting.

Packaging:

1 liter, 5 liters, 18 liters

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Storage:

In a cool, shady place at the temperature of the room with proper ventilation.
Keep a tightly closed lid.

Shelf life:

12 months in the original packaging.

Tools Cleaning:

Thinner 21-D immediately after painting.

Safety precautions:

Not edible, out of reach of children.
Flammable, away from heats, fire.
Ensure proper ventilation during application.
Wear goggles, solidarity gloves, protective clothing.
In case of injury , seek medical attention immediately.

Denberust Phenolic HD Middle layer

Phenolic mid. layer coat.

Warnings:

Do not mix with materials not recommended by us.
Avoid contact with the skin and eyes, causing dryness and irritation of the skin. In contact, rinse with plenty of running water and seek medical attention.

Quality review:

In our factory laboratories in accordance with data sheets
ISO 9001-2015

Please note: This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Names of consultants/professional instructors can be obtained by telephone. Read product MSDS safety instructions before starting work with it. Manufactured by Denver Colors & Coatings Israel Ltd., 80100 Sderot, 80100, certified by the Standards Institution of Israel in accordance with ISO 9001-2015 standards

Denberust Phenolic HD Middle layer