Epoxyden Floor А4 65% solids, 2:1

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

For pouring 0.5-1 mm thickness floor/wall coating. Can be spread easy self leveling or spray with airless. Tinted heavy duty industrial wall and floor paint.

Double component polyamine epoxy, for painting or pouring industrial floors and painting walls. For harsh and extreme condition endurance. Has excellent chemical and erosion durability. A smooth surface that has light to medium load endurance.

Epoxyden Floor А4 65% solids, 2:1. www.denber-paints.co.il

Epoxyden Floor А4 65% solids, 2:1. www.denber-paints.co.il

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

Properties :

  • Heavy duty, Very strong.
  • Paints easily.
  • Has alkali acid durability according to the table below.
  • Durable against industrial polluted water for long periods of time.
  • Durable against fuels and oils.
  • and Durable against cleansing and other pungent chemicals.
  • Durable against scratches, hits and heavy loads.
  • Appropriate for industrial walls and floors that heavy equipment and cars move on it.
  • Covers the floor with an even and smooth coat that has no stitches.
  • Easy to clean and leaves a clean floor after an ordinary wash.
  • Excellent adhering ability to Epoxyden floor primer layers.
  • High mechanical strength and excellent erosion durability.
  • Durable in dry heats of up to 200°C on short periods of time and up to l50°C for long periods of time.
  • Easily repairable at very low costs.
  • High electrical isolation.

Applications:

  • For coating walls and floors in industries, private car garages and warehouses.
  • For electrical, hi-tech, medicine and food industries that need high sanitation standards.
  • And For slaughter houses, dairy barns, kitchens and etc..
  • For places that require smooth, easy to wash coating where the floor is usualy dry.
  • For rough anti-slipping coating in areas where the floor is wet or greasy, if it is required to increase the roughing material- sprinkle quartz on the paint while it is still wet.

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

Technical specifications:

  • Amount needed per For 40 mic. dry film – 1 liter per 16 sqm.
  • Theoretical coverage: 1 liter per 16 sqm.
  • Recommended layer thickness – 40 mic.
  • Recommended no. of layers – 1-2 for walls, 2-4 for floors.
  • Density: 6-1.7 gm/cm3(DIN 51575)
  • Solids – 65% matt, 47% gloss.
  • Mixing ratio by volume: 2.5:1
  • Hardness: >10 Dg (ERICHSEN) (over 60 DIN 53153)
  • Flexibility: film 120 microns – 2mm (SHEEN).
  • Viscosity: 12,000-15,000 CPS (BROOKFIELD)
  • Erosion endurance: 4100 cycle (Gardener) ATSM, roll CS,-17 l kg load, 1000 cycles, 45 milligrams lose, according to ASTM 4060 standard.
  • Adhesion to concrete: stronger than the concrete.
  • Adhesion to Epoxyden floor primer: 245kg per cm.
  • Flexibility in drag 10% N/mm 2  (DIN 53457)

Contains:

  • High-quality Epoxy resin mixture.
  • Self- leveling additives.
  • Fillers.
  • Solvents.
  • Additives.

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

Color :

  • Red, Gray, Green, Yellow, Blue or in other less durable shades.

Gloss :

  • Glossy

Touch-dry time:

  • 1 hour at 25°C for a 100 micron layer.

Wait time period between layer applications:

  • 12-16 hours. Final 24-48 hours. Finish: 3-7 days (figures change according to the temperature).

Curing time for 500 micron layering:

Temperature First cure Final cure
7°C 96 hours 6 day days
10°c 48 hours 5 days
15°C 30 hours 3 days
20°c 24 hours 3 days
30°C 18 hours 2 days
40°C 12 hours 1 day

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

Application  methods:

  • Pour and spread with hard wiper and go over with stich roller to takeout the air.

Thinning:

  • Add a small amount in order to ease the spraying or To coat small areas it is required to make a suitable amount of mixture for immediate use.

Surface preparations:

  • It is required to apply on the Epoxyden floor primer surface only if it is completely clean and dry.

Instructions:

  • Make sure that the primer layer is dry, clean any dirt, dust and grease.
  • Open carefully parts A and B of the paint and pour B to A in ratio 2.5: 1 the required amount. Stir well and immediately pour on the edge surface floor.
  • With a large wiper spread the mixture evenly on the entire surface or spread desired layer thickness with suitable roller.
  • It is recommended not to move any heavy equipment such as forklifts on the surface for at least 7 days.

Pot Life after mixture according to the temperature:

5 liters of A +B mixture
10°c 4.5 hours
15°C 3 hours
20°c 2 hours
25°C 1.5 hours
30°C 1 hour
35°C 45 minutes

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying

Package:

  • 3.6+1.4 =5 liters, 5+13= 18 liters ,

Storage:

  • Store in a shaded place, at a temperature of between 15°C-32°C with proper ventilation.
  • Keep lids tightly closed.

Shelf life :

  • 24 months in its original package.

Equipment cleansing:

  • Use D-4/100 thinner immediately afteruse.

  Quality control:

  • In factory laboratories according to specifications.
  • COA and COC certificate.
  • ISO 9001-2015

Safety precautions:

  • Inedible, keep away from the reach of children.
  • Flammable – keep distant from heated areas, fires, flames, and sparks, Prohibit smoking in working area.
  • While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
  • Wear protective glasses, gloves and suits.
  • Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
  • In case of an injury immediately get doctors assistance.
  • Read the safety instructions on the labels.
  • See M.S.D.S

Epoxyden Floor А4 65% solids, 2:1

Floor and wall thick coat 0.5-1 mm pouring or spraying