Epoxyden Floor Antistatic colors. DENBER PAINTS

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Epoxyden Floor Antistatic colors. www.denber-paints.co.il

Two component epoxy, with electrical conductivity, to form a smooth self-leveling (without stitches) antistatic floor coating of 1-3 mm. thickness by pouring and spreading the product on the floor. The coating has excellent chemical and corrosion resistance as well as against scratches. The product is durable in harsh and extreme conditions including heavy load traffic on the surface.

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Properties:

To ground all the electrical currents of the static electricity along the coat and through the copper stripes that is under the coating to the ground point.
Heavy duty-thick layer.
Easy pouring-self leveling
100% solids – no solvent evaporation.
Has alkali and acid durability according to the table below.
Durable against industrial polluted water for long periods of time.
Durable against fuels and oils.
and Durable against cleansing and other pungent chemicals
Durable against scratches, hits and heavy loads.
At a thickness of 3mm the coating is suitable for floors that endure heavy logistical equipment, and at a thickness of 1 mm the coating is suitable for medium loads and for pedestrians.
Covers the floor with an even and smooth coat that has no stiches.
Easy to clean and leaves a clean floor after an ordinary wash.
Excellent adhering ability to Epoxyden floor antistatic primer layer.
High mechanical strength and excellent erosion durability.
Durable in dry heat of up to 200°C on short periods of time and up to 100°C for long periods of time.
Easily repairable at very low costs.
Doesn’t contain any thinners enabling application at minimal ventilation.

Application:

For coating floors in electronic industries that static electricity affects the equipment used.
For industries that cannot tolerate a single spark that could cause fires.
and For a smooth coating for hi-tech industries that require high cleanliness standards.
For static electricity control in the production room.

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Technical specifications:

Amount needed per sqm: For a thickness of 1 mm -1 liter per sqm.
For a thickness of 3 mm – 3 liters per sqm.
Density: 3-1.7 gm/cm3 (DIN 51575)
Solids % – 100%
Mixing ratio: 2.5:1
Flash point: Base 255°C, hardener at 166°C (isn’t flammable , doesn’t contain solvents) (DIN ,53213 53213 )
Hardness: > 10 Dg (ERICSON) (over 60 DIN 53153)
Flexibility: film 120 microns – 4mm (SHEEN).
Flex-resistance: 8 N/mm²(DIN 53452)
Flex potency: 30 N/mm²
Viscosity: 12,000-15,000 CPS (BROOKFIELD)
Stretch resistance: 600kg per cm².
Pressure resistance: per cm².
Erosion endurance: 4500 cycle (Gardener) ATSM, roll CS,-17 l kg load, 1000 cycles, loss of 40 milligrams, according to ASTM 4060 standard.
Impact resistance: 2.0 Dg/mm²
Adhesion to concrete: stronger than the concrete.
Adhesion to Epoxyden floor primer: 245kg per cm.
Flexibility in drag: 10% N/mm² (DIN 53457)
Drag resistance: 8 N/mm²(DIN 53455).

Electrical details:

Surface resistance: 25-1.0 Mega ohm (ASTM F 150-89)
Resistance to the ground without copper stripes: same as
Resistance to the ground at a thickness of l mm: 60-425 ohm,
and Resistance to the ground at a thickness of 3mm: 180-1500 ohm

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Contains:

Special Epoxy resin mixture.
Conductive polymers.
Self-leveling additives.
Special fillers.
Conductive fillers.
additives.

Colors:

Black, grey light and dark, blue-grey, green-grey, yellow-grey.
To order other colors requires another part of the product that contains special filler (part C). This part is added to the A and B mixture and immediately colors it, using this method you can (though not recommended) get any color wanted and not add the copper strips.
Emphasizing the fact that the copper stripe method proved itself throughout the years as reliable, therefore the required conductance at any point on the surface has the same conduction from that point to the copper stripe l -3mm under the inspection point or max. 50 cm. from the inspection point.
Though without the copper stripes conduction is required throughout all the surface until reaching the ground point that could be a great distance especially in large halls that could reach tens to hundreds of meters.
If static stability control is required, the copper stripes must be used.

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Gloss :

Silk, gloss

Touch-dry time:

4-8 hours at 25°C for a 1 mm layer.

Wait time period between layer applications:

12-16 Final 16-24 hours. Finish: 3-7 days (figures change according to the temperature).

Ventilation:

Does not contain any solvents so that a medium amount of air is required.

Application time of 500 micron layer:

Temperature		First appliance	Final appliance
7°C		96 hours	15 days
10°c		48 hours	10 days
15°C		30 hours	7 days daysdays
20°c		24 hours	3 days
	30°C	18 hours	2 days
	40°C	12 hours	1 day

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Application methods:

Pour and spread with hard wiper and it will self-level.

Thinning:

No thinning
Add a small amount in order to chill the mixture if a heat reaction has accord preventing it from drying quickly and increasing its pot life.

Surface preparations:

It is required to apply on the Epoxyden floor primer surface only if it is completely clean and dry.
It is possible to repair small and large surfaces with grout epoxy before applying Epoxyden floor primer.

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Instructions:

Spread a thin layer Epoxyden floor primer (antistatic black) over the entire surface according to the instructions manual for the product, wait 24 hours till it The mixture ratio of the primer is 2.5:1 or 1:1 and reacts exactly like paint, easy to apply and is suitable for applying the copper stripes on.
Apply/glue the copper stripes all over the primer surface in 1 meter distance between the lines. Glue them horizontally and vertically.
With a brush using the Epoxyden floor primer as glue cover totally all the copper strips.
At the edges of the surface weld those connecting copper wires to the It is recommended to have four different connects to the ground.
Make sure that the primer layer is completely dry and clean from dust, dirt and grease free. Check if the copper stripes stuck well to the primer and the welding is The welding stains should be removed carefully with degerizer M without damaging the primer layer. Any damage must be repaired. Therefore waiting needed until it completely dries.
Open carefully sections A and B of the Epoxyden floor antistatic and pour the required amount according to the ratio of 5:1 (for example for a thickness of l mm it is required to prepare 1 liter mixture per 1 sqm. surface. Therefore to cover a 10 sqm. surface requires 10 liters of mixture)
Stir the mixture well then immediately pour the mixture on the edge of the surface floor.
With a large rubber wiper spread the mixture evenly coating the floor according to the calculation in the required thickness.
It is recommended not to move any heavy equipment such as forklifts or trucks on the floor before at least a week has passed after the application.

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Static electricity created by walking on the floor (average figures):

Isolated shoes: 60-150 volts.
Leather shoes: 12-50 volts
Special plastic antistatic shoes: 10-30 volts.

Uploading time period (of 500 volts) of static electricity that form while walking with these shoes:

Isolated shoes: 3-8 seconds.
Leather shoes: 25-2.5 seconds
Special plastic antistatic shoes: 05-1 seconds.

Life span after mixture (POT LIFE) according to the temperature:

5 liters of A +B mixture
10°C	1 hour
15°C	45 min.
20°c	30 min.
25°C	25 min.
30°C	20 min.
35°C	15 min. minutes

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Package:

3.4+1.6=5 liters, 5+13= 18 liters

Storage:

Store in a shaded place, at a temperature of between 15°C-32°C with proper ventilation.
Keep lids tightly closed.

Shelf life span:

24 months in its original package.

Equipment cleansing:

Use D-4100 thinner immediately after pouring the floor.

Quality control:

In factory laboratories according to specifications.
COA and COC certificate.
ISO 9001-2015

Epoxyden Floor Antistatic colors

Antistatic epoxy paint floor coating in colors 100% solids

Safety precautions:

Inedible, keep away from the reach of children.
Flammable – keep distant from heated areas, fires, flames, and sparks, Prohibit smoking in working area.
While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
Wear protective glasses, gloves and suits.
Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
In case of an injury immediately get doctors assistance.
Read the safety instructions on the labels.
See M.S.D.S

Epoxyden Floor Antistatic colors