Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature

Aluma silicon 540 antistatic electric conductive www.denber-paints.co.il
Aluma silicon 540A is a high temperature resistance (up to 540oC) Antistatic, electric conductive organic silicon resin top layer paint. Produced in gray or black shades. A top industrial hard paint based on special organic silicon resins for painting high heat emitting elements up to 540O C. The paint is cured without external heating. Providing protection and resistance to high heat emitting elements, as well as for electro static electricity grounding.
Suitable to paint: turbines, heat exchangers, chimneys, stoves etc.
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
Properties:
- High temperature resistance up to 540O C.
- Electric conductive.
- Fast drying top layer paint.
- Resistant to humid conditions.
- Easy to apply, dries fast without additional heating.
- Economical, high coverage area.
- Suitable for indoor and for outdoor applications.
- Excellent adhesion to a proper primer.
Applications:
- Top layer paint suitable for painting: chimneys, stoves, heat exchangers, turbines, hot working surfaces, hot piping, engines, gas engines, boilers, instruments for heating, fuel and gas systems and pipes, hot oil systems, cooking & backing equipment, heat exchangers, exhausting systems for hot gages etc.
- Useful for electro static electricity grounding.
Technical Data:
- Theoretically area covered: 1 liter for 8 m2
- Consumption: 125 microns wet layer leaves 25 microns dry.
- Solids content: 20 %
- Flexibility: 3 mm (Sheen).
- Density: 1.2-1.3 gm/cm3
- Viscosity: 2000 cPs (Brookfield)
- Hardness: >10 Dg (Erichsen) after heating in oven at 200°C during 50 seconds.
- Recommended layer thickness 90 microns dry film.
- Recommended number of layers: 1-2
- Erosion: 40 mic. layer – 1560 cycle (BYK Gardener)
- Heat resistance: 540o C (ASTM D2485-91)
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
Electricity details:
- Surface resistance: <0.25-1 mega ohm (ASTM F 150-89)
- Resistance to ground: without cuprum strips – <0.25-1 mega ohm.
Contents:
- Special organic silicon combustion resins.
- Electro conductive promoters and materials.
- High temperature Aluminum powder, carbon black and high temp. pigments.
- Flexible materials.
- Solvents, additives.
Colors:
- Gray, black.
Gloss:
- Matte/glossy.
Touch dry time:
- 1-2 hours.
Drying between layers:
- 6 hours: final 24 hours in room temp.
- Final hardness achieved after 3 days.
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
Methods of application:
- Spray, brushing, roller.
- First layer by spraying.
- Second layer with roller.
- If the material is not uniform and behaves like mercury (forming drops) due to inner high pressure stress, the surface is to be painted and after waiting 60 seconds paint again, until a smooth surface is obtained.
- It is recommended to mix the paint well before and during painting.
Thinning:
- Thinner D-32
- Spraying: 5-10% thinner D-32 pressure 4-5 atm. (can do without thinning).
- Brushing/roller: up to 5% (can do without thinning).
- Airless: 0-5% thinner D-21 pressure 5-6 atm. 0.015” nozzle (can do without thinning).
Surface preparation:
- Mechanical or chemical cleansing until metal is white.
- Mechanical: grade ST3 steel brushes.
- Chemical: rust remover 3000; grease/oils with degreaser M.
- Sand blasting grade: SA 2.5
- The surface must be clean from dust, dirt, grease or loose paint.
- For repainting top coat – spray hot water in 150- 200 atm. pressure and let it dry completely.
- Sand lightly with glass paper and clean thoroughly.
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
Primer:
- On iron metals: zinc silicate.
- On other not rusted metals: apply directly the paint but see there is a proper and steady adherence.
Packaging:
-
- 1 liter, 2.5 liters, 5 liters, 18 liters.
Storage:
-
- At shaded room temperature in protected place with proper ventilation.
- Keep lids tightly closed.
Shelf Life:
-
- 12 months in original packaging.
Tools Cleansing:
-
- D-21 immediately after finish painting.
Quality control:
- In factory laboratories according to specifications.
- COA and COC certificate.
- ISO 9001-2015
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
Safety precautions:
- Inedible, keep away from the reach of children.
- Flammable – keep distant from heated areas, fires, flames, and sparks, Prohibit smoking in working area.
- While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
- Wear protective glasses, gloves and suits.
- Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
- In case of an injury immediately get doctors assistance.
- Read the safety instructions on the labels.
- See M.S.D.S
Aluma silicon 540 antistatic electric conductive
Antistatic electric conductive for high temperature
- For more information about Denber Paints and Denber Projects, please contact us by phone and/or to the company’s websites:
- company profile English also
- For more details please refer to the Denber website also
- For our Facebook page click here also
- To the Facebook page of the CEO of Denber also
- For more projects click here also
- To the article: Sealer for stone and concrete and marble also
- To the article: Thermal insulation in nanotechnology also
- article: Thermal insulation Thermosil 200 energy saving in green construction also
- Related article: Thermal insulation, floor coating also
- To the article: Thermal insulation in nanotechnology company Denber also
- Fire resistance of houses, hardwood and parquet floors, decks also
- Swelling paints for steel protection against fire – Fire retardant paint also
- Epoxy floor coating in casting and painting also
- Crystal epoxy resin for tables also
- To the article Sealing also
- The complete article on the sealing materials for roofs and walls also
- Sealing the floor of the balcony, terrace from rain also
- Mold, how to remove mold correctly and how to fight mold also
- “Sick” buildings – Antibacterial paints Bacterinoll/ Tutgum Bacterinol also
- Paint for aircraft Denbergloss Jets also
- Asphaltflex execution specification – Denber Paints also
- Denbergloss grainy car paint also
- Denbergloss Clear also
- Varnish for wood. How to choose the right varnish for wood also
- Crystal epoxy for tables from Denber also
- Paint for swimming pools, epoxy Epoxyden Dengal, performance specification also
- Color specification of quadrant helmets also
- For a free consultation, call Denber – Dr. Blen Evgenia – 050-3551549 / 050-3551551 also
- Need advice? Contact us by email: Denber@bezeqint.net or contact us at 08-9960794