Epoxyden crystal clear for pouring tables

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES www.denber-paints.co.il

Epoxy high build and heavy duty for pouring. It is a two-component product, 100% solids, self-leveling. Special for coating by pouring monolithic crystal-clear tables, jewelry, models and sculptures. Produced in clear and variety of colors.

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Properties:

Can be poured in one thick layer without thickness limiting.
100% solids, no solvents evaporation.
Smooth and high hardness finishing, scratch durable.
Gives the appearance like monolithic glass.
Easy to wash and reject dirt and dust.
Durable in washing chemicals.
Can be poured clear coat on colored with pigments.
Suitable for tables and 3D pictures and art works.
Very good adhesion to any hard infrastructure. Including wood, cement and steel alloy with appropriate primer coat.
Easy to apply as it is self-leveling.
Resistance to heat and cold.
Durable in high humidity.
Smooth ang glossy.
Not good for direct exposure to the sun. Must be coated with Denbergloss clear.
Does not contain cadmium, lead, chromates.

Applications:

Pouring tables, sculptures, models, jewelry etc.

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Technical data:

Part A– clear, can be mixed easily, and in 5 minutes you’ll receive a smooth and uniform solution.
Part B – transparent and clear.
Storage durability – 24 hours at 57⁰ C with no sagging or corruption.
Coverage – 1 liter to 1 sqm. in 1 mm. and 3 liter to 1 sqm in 3 mm thickness and so on.
Recommended thickness of layer- 3mm to unlimited.
Density – 1.0-1.2 gm\cm³ for clear, 1.1-1.3 for tinted.
% Solids – 100%.
Ratio – 2:1 by weight (base-2, hardener-1), or 1:0.6 by volume.
Flash point part A – 255^O part B – 166^OC
Hardness – >10 Dg (Erichsen)
Elasticity – 4 mm (sheen)
Bending strength – 30 N/mm²
Viscosity average A + B – 12,000cPs (Brookfield)
Pressing strength – 800 kg/cm²
Elongation strength – 600 kg/cm²
Friction – 120 microns – 4500 cycles (Gardner) ASTM
Impact strength – 2.0 Dg/mm²
Adhesion to concrete – higher than concrete strength.
Adhesion to Epoxyden floor primer – 245 kg/cm²
Elasticity in dragging – 10% N/mm² (DIN 63457)
Dragging resistance – 8 N/mm2 (DIN 53455)

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Electric isolation for clear coat – 5×10¹⁴ ohm/cm³
Pot life = working time from mixing A + B – < 20 minutes.
Distilled water resistance for 24 hr. Without losing adhesion or corrosion 1 hr. after taking out of water.
Carbon resistance – no loss of adhesion durability 1 after taking out of the solvent.
Resistance to oil 1250 24 hours in 121^oC. No loss of adhesion 4 hours after taking out of the oil.
Hydraulic oil resistance 24 in 66^oC. Without losing adhesion 4 hours after taking out of the oil.
Aviation Fuel resistance – 7 days in room temp. Without losing adhesion 4 hours after taking out of the fuel
Heat resistance 121^O C during 60 minutes – NO shade changes to Delta E = 1.
Humidity cabinet – 30 days in 100% humidity in 49^oC. No loss of adhesion or damage to the film after 1 hr. out of cabinet.
Salt spray durability – 3000 hours with no corrosion occurs.
Thermal shock – without adhesion loses.

Contains:

Crystal Epoxy resin.
Hardener.
Additives.

Colors:

Clear

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Gloss:

Glossy

Touch dry time:

<12 hours.

Drying between layers and final:

16-24 hours, final: 24 hours, hard to use: 7 days

Application methods:

Pouring and leveling with tooth spatula or roller, and taking of the air with thorns roller or hot air.

Ventilation:

No solvent evaporation, 100% solids. Minimum ventilation needed.

Dilution:

Without dilution.

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Surface preparation:

Wooden tables: prepare the form for the proper size. Spray silicon fog on the form. The wooden parts need to be coated with Isolation day earlier before put in the form. Pour the mixed crystal epoxy until all the form is full.
Preparing concrete tables: polishing with diamond stones in vacuum or shot blast machine.
Perfect cleaning from dust, dirt or grease or loose paint with degreezer M
Primer Epoxyden 450 for damp floors or Epoxyden floor primer – standard primer.
Fill holes with grout epoxy.
Open the concrete cracks and stitches and fill with elastomeric 225A.
With Diamond disk make thresholds (mechanical anchor) width of 1 cm and depth of 5 mm. In steel connection with concrete. This will be about 1 cm slot from the steel.
Preparing metal surfaces: mechanical cleaning with brushes made of steel or clean with sand blast to get white metal SA 2.5. Chemical cleaning: removing rust and chemical burning with Denber rust remover 3000 and grease removing with Degreaser M

Primer:

For concrete – Epoxyden floor primer
For steel – Epoxyden antirust rust converter.
and For wood – Isolation.

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Packaging:

1+2 = 3 kg
3.35+1.65= 5 kg
10+5 = 15 kg

Storage:

In a cool shaded place in room temp. with proper ventilation.
Keep lids tightly closed.

Shelf life:

24 months in original package.

Tools cleaning:

Thinner 4/100-D at the end of painting.

Quality control:

In factory laboratories according to specifications.
COA and COC certificate.
ISO 9001-2015

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES

Clear pure epoxy

Safety precautions:

Inedible, keep away from the reach of children.
While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
Wear protective glasses, gloves and suits.
Avoid direct contact of the epoxy with the eyes and skin. In case of contact, immediately wash thoroughly with water.
In case of an injury immediately get doctors assistance.
Read the safety instructions on the labels.
See M.S.D.S

Clear pure epoxy

Warnings:

Don’t mix the product with materials which were not recommended by us.
Don’t apply if the temperature is under +7°C.
and Don’t apply if humidity is over 80%
When applying with Airless. Do not aim it at anybody a direct hit could be fatal at pressures over 150 atm.
Read thoroughly the technical data of the product listed in this section. Confirm that everything is understood completely. For clarification contacts our tech. department.
All information that is listed in this content is a recommendation merely, and cannot be applied in the court of law.
The costumer must test & check that this product is compatible with his equipment and needs.
The information listed in this section is according to the laboratory conditions (temperature, humidity etc.). Which the products were tested.
and The recommendations listed do not hold any responsibility for this product.
Theoretical and actual coverage area are different concepts. The actual coverage is affected by the required thickness of the layers. Required number of layers and painting conditions, including the amount of paint which spread in the air before touching the surface.
The information listed in this section is based on experience and accumulating data. Denber inc., has the right to change the information listed at any time.
Paints that have been in stagnation or exposed to air more than needed could have their qualities changed.

EPOXYDEN CRYSTAL CLEAR FOR POURING TABLES