Spray Vitraz Glass Paint

Spray Vitraz Glass Paint

Decorative glass paint

SPRAY VITRAZ CLEAR TINTED PAINT FOR GLASS – fast drying spray paint for painting glass in shades.

Spray Vitraz Glass Paint. www.denber-paints.co.il

Spray Vitraz Glass Paint. www.denber-paints.co.il

Decorative glass paint

Features:

  • Transparent and decorative color in shades of glass.
  • Spray is easy and easy to use.
  • Turns every transparent glass into a multi-tone stained glass.
  • Very strong adhesion to glass.
  • For application in one uniform layer.
  • If an extra layer is required for perfect coverage, waiting time between layers is short due to the rapid drying.
  • Excellent inter layered connecting ability.
  • Resistant to heat and cold.
  • For application in a thin, economical layer.

Uses:

  • For the self-production of stained glass.
  • For artwork.

Decorative glass paint

Technical data:

  • Theoretical coverage capacity – 1 liter to 8-10 square meters
  • Number of layers recommended – 1
  • % solid in aerosol volume 400 ml – 100 g liquid color per 400 ml total volume. 15% solid.
  • Color pigment content – 45% (T.I. 785 Part 19)
  • Adhesion – Criss cross cut “0” (T.I.P. 785 Part 27 Film 50 mic 7 drying days)
  • Flexibility – 1 mm (sheen) meets israeli standard 935 section 307.
  • Grinding – up to 2 microns (T.I.785 Part 15) (Hegman)
  • Density – 0.8-0.9 gm\cm3
  • water immersion resistance – no bubbles, No softening, no change in adhesion, (T.I.935 Section 312)
  • Resistance to “bleeding” – no less than level 6 according to ASTM D-868 and ASTM D-969
  • Radiation resistance – 1,200 hours in Q-Pannel with UVA-340 lamp in 8-hour light cycles at O60 temperature and 4 hours at O50 temperature, (tested by ASTM D-4587-91) – Gloss loss : 4%
  • Viscosity – room temperature 0.5-1.0 Pa.sec (HAAKE) 110-120 Krebs in 200 rounds per minute after manual mixing of 2 minutes (T.I.935 Section 302), after diluting 10% in the thinner – 85-90 Krebs. After 10 days it is stored at 42ºC – the position will increase to 5 krebs.
  • Rigidity – 3 Dg< (Ericsson)
  • Abrasion – 120 microns – 200 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 g per 500 cycles (device – up to 2.5 g licensed loss) exfoliation strength – minimum 1 kg per square cm.
  • Heat resistance up to 70 °C unchanged in features and deformation.
  • Recommended layer thickness –5-10 microns dry.
  • Flash point – 25OC

Decorative glass paint

Contains:

  • Fillers
  • solvents
  • Resins, pigments.
  • Adehyesia enhancers.
  • Additives.

Shade:

  • Red bordO, red blood, pink, blue, light blue, deep green, light green, lemon yellow, mustard, turquoise, orange, purple, and more.

Gloss:

  • Silk , (T.I.935 Section 309).

Drying to the touch:

  • 10-15 minutes depending on the temperature of the environment. Drying time on the wheel – (T.I.935 Section 304 Repair No. 2) – up to 45 minutes

Decorative glass paint

Drying between layers:

  • 20 minutes, Final: 3-4 hours (depending on the ambient temperature)

Application methods:

  • Aerosol spray spray in splash.

Preparation of area:

  • Thorough cleaning dust, fat, dirt, it is recommended to rinse with an AA incuster that evaporates after cleaning and leaves clean and dry glass. To finish wipe well with soft tissue towel paper.

To use:

  • After wiping the glass, place the glass on a straight surface lined with paper to prevent environmental dirt while spraying.
  • Remove the aerosol lid and shake well until you hear the sound of the marbles that help mix.
  • Spray a thin, uniform layer on the glass surface.
  • Wait about 20 minutes to dry.

Decorative glass paint

Packaging:

  • 0.4 liter Spray container.

Storage:

  • In a cool, shady place at room temperature.
  • Keep lids tightly closed.

Shelf life:

  • 12 months in the original packaging.

Cleaning tools and dirt created:

  • Synthetic diluter 18-D immediately after painting.

Safety:

  • Not edible, out of reach of children.
  • Flammable, away from heats, fire and sparks.
  • Ensure proper ventilation during application.
  • Wear goggles, solidarity gloves, protective clothing.
  • In case of injury , seek medical attention immediately.

Decorative glass paint

Warning:

  • Do not mix with unsalted ingredients. Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening. Recommended in heats not exceeding 30 degrees and humidity of up to 50%.
  • Avoid contact with the skin and eyes, causing dryness and irritation of the skin.
  • In contact, rinse with plenty of running water and seek medical attention.
  • Pressure tank, empty before tossing. Do not throw into the fire – may explode.

Quality audit:

  • In our factory laboratories in accordance with iso 9001-2015 specifications

For user attention: This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Names of consultants/professional instructors can be obtained by telephone. Read product MSDS safety instructions before starting work with it. Manufactured by Denver Colors & Coatings Israel Ltd., 80100 Sderot, 80100, certified by the Standards Institution of Israel in accordance with ISO 9001-2015 standards

Decorative glass paint