Spray Shasiss Rubber coat
Flexible black synthetic rubber
Synthetic rubber spray for bottom field vehicles chassis – fast drying liquid synthetic rubber coat, for filling cracks, sealing from water penetration and noise isolation.

Spray Shasiss Rubber coat. www.denber-paints.co.il
Flexible black synthetic rubber
Features:
- Fast drying synthetic liquid rubber suitable for isolation coat against water penetration into the floor of SUVs.
- Perfect isolation for water penetration and noise insulator.
- A very strong adhesive capacity for the vehicle’s chassis.
- Can be applied in multiple layers for desired thickness to fill cracks and gaps between bins.
- Short waiting time between layers due to the rapid drying.
- Excellent inter layered connecting ability.
- Resistant to heat and cold and extreme weather conditions as well as salty seawater and fresh water.
- Flexible and strong.
- Resistant to scratches and shocks.
- Easy to apply in a spray.
Uses:
- Floor chassis coating for sealing water penetration and noise insulation.
Flexible black synthetic rubber
Technical data:
- Theoretical coverage capacity – 1 liter per 8-10 square meters.
- Practical consumption per layer of 100 microns – 150 ml liquid rubber per square meter for 100 microns of dry layer (minimum required).
- Recommended number of layers – 2-4
- % solid in volume – 60% (T.I.785 Part 17).
- % solids in aerosol volume – 100 g liquid rubber per 400 ml total volume.
- Adhesion – Criss cross cut test “0” (TA 785 Part 27 Film 50 mick 7 drying days)
- Flexibility – 1 mm (sheen) meets the israeli standard test 935 section 307.
- Density – 1.1-1.2 gm\cm3
- Resistance to immersion in water – no bubbles, No softening, no change in Adhesion, (T.I.935 Section 312)
- Resistance to “bleeding” – no less than level 6 according to ASTM D-868 and ASTM D-969
- Radiation resistance – 1,200 hours in Q-Pannel with UVA-340 lamp in cycles of 8 hours of light at the O60 temperature and 4 hours at temperature of O50 , (tested according to ASTM D-4587-91) – lightning loss : 4% stiffness – 3 Dg< (Ericsson) abrasion – 120 microns – 850 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 g per 500 cycles (standard – up to 2.5 g authorized loss) exfoliation strength – minimum 5 kg per square cm.
- Heat resistance up to 70 °C unchanged in features and deformation.
- Recommended layer thickness – 150 microns wet.
- Flash point – 25OC
Flexible black synthetic rubber
Contains:
- synthetic rubber
- solvents
- Fillers
- Adhesion enhancers.
- Additives.
- Gas
Hue:
- Black
Gloss:
- Silk , (T.I.935 Section 309).
Drying to the touch:
- 10-15 minutes depending on the temperature of the environment. Drying time on the wheel – (T.I.935 Section 304 Repair No. 2) – up to 45 minutes
drying between layers:
- 20 minutes, Final: 3-4 hours (depending on the ambient temperature)
Flexible black synthetic rubber
Application methods:
- Spray with aerosol.
Dilution:
- None.
Field preparation:
- Thorough cleaning dust, fat, dirt, mud, it is recommended to rinse with a lipid removal deagency if any, rinsing with fresh water and waiting to dry, to ensure cleanliness of the area before painting.
Packaging:
- 400 ml spray.
Storage:
- In a cool, shady place at room temperature.
- Keep lids tightly closed.
Flexible black synthetic rubber
Shelf life:
- 12 months in the original packaging.
Cleaning tools:
- Synthetic thinner 18-D immediately after painting.
Safety:
- Not edible, out of reach of children.
- Flammable, away from heats, fire and sparks.
- Ensure proper ventilation during application.
- Wear goggles, solidarity gloves, protective clothing.
- In case of injury , seek medical attention immediately.
- Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening.
- Recommended in heats not exceeding 30 degrees and humidity of up to 50%.
Flexible black synthetic rubber
Caution:
- Do not mix with materials not recommended by us.
- Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening.
- Recommended in heats not exceeding 30 degrees and humidity of up to 50%.
- Avoid contact with the skin and eyes, causing dryness and irritation of the skin. In contact, rinse with plenty of running water and seek medical attention.
- Aerosol Spray is a pressure tank, it must be emptied of gas before being thrown in the trash. It should not be thrown into the fire. There is a risk of exploding.
- Quality Review:
- In our factory laboratories in accordance with
- ISO 9001-2015 specifications
Flexible black synthetic rubber
Please note: This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Names of consultants/professional instructors can be obtained by telephone. Read product MSDS safety instructions before starting work with it. Manufactured by Denver Colors & Coatings Israel Ltd., 80100 Sderot, 80100, certified by the Standards Institution of Israel in accordance with ISO 9001-2015 standards
Spray Shasiss Rubber coat
Flexible black synthetic rubber
- For more information about Denber Paints and Denber Projects, please contact us by phone and/or to the company’s websites:
- company profile English also
- For more details please refer to the Denber website also
- For our Facebook page click here also
- To the Facebook page of the CEO of Denber also
- For more projects click here also
- To the article: Sealer for stone and concrete and marble also
- To the article: Thermal insulation in nanotechnology also
- article: Thermal insulation Thermosil 200 energy saving in green construction also
- Related article: Thermal insulation, floor coating also
- To the article: Thermal insulation in nanotechnology company Denber also
- Fire resistance of houses, hardwood and parquet floors, decks also
- Swelling paints for steel protection against fire – Fire retardant paint also
- Epoxy floor coating in casting and painting also
- Crystal epoxy resin for tables also
- To the article Sealing also
- The complete article on the sealing materials for roofs and walls also
- Sealing the floor of the balcony, terrace from rain also
- Mold, how to remove mold correctly and how to fight mold also
- “Sick” buildings – Antibacterial paints Bacterinoll/ Tutgum Bacterinol also
- Paint for aircraft Denbergloss Jets also
- Asphaltflex execution specification – Denber Paints also
- Denbergloss grainy car paint also
- Denbergloss Clear also
- Varnish for wood. How to choose the right varnish for wood also
- Crystal epoxy for tables from Denber also
- Paint for swimming pools, epoxy Epoxyden Dengal, performance specification also
- Color specification of quadrant helmets also
- For a free consultation, call Denber – Dr. Blen Evgenia – 050-3551549 / 050-3551551 also
- Need advice? Contact us by email: Denber@bezeqint.net or contact us at 08-9960794