Spray paint for Aluminum
Aluminum frames paint
TINTED SPRAY PAINT FOR ALUMINUM- fast drying, in any shade from catalog RAL, Panton, Fed. st. and others

Spray paint for Aluminum. www.denber-paints.co.il
Spray paint for Aluminum
Aluminum frames paint
Features:
- Fast drying paint for scratched/damaged paint repairs in the area after assembly.
- Spray easy to use.
- A very strong adhesion capacity to aluminum in particular and for various infrastructures in general.
- For application in one uniform layer.
- If an extra layer is required for perfect coverage, waiting time between layers is short due to the rapid drying.
- Excellent inter layered connecting ability.
- Resistant to heat and cold and outdoor conditions.
- For application in a thin, economical layer.
Uses:
- Paint repairs in aluminum frames after assembly.
- For markings.
- For damaged paint repairs and general painting.
- For artworks.
Spray paint for Aluminum
Aluminum frames paint
Technical data:
- Theoretical coverage capacity – 1 liter per 8-10 square meters.
- Number of layers recommended – 1
- % solid in eurosol volume 400 ml – 100 g Concentrated liquid paint per 400 ml total volume. 50% solid.
- Pigment content – 45% (T.I. 785 Part 19)
- Adhesion – Criss cross cut “0” (T.I.P. 785 Part 27 Film 50 mic 7 drying days)
- Flexibility – 1 mm (sheen) meets israeli standard 935 section 307.
- Grinding – up to 2 microns (T.I.785 Part 15) (Hegman)
- Density – 0.8-1.0 gm\cm3
- Resistance to immersion in water – no bubbles, no softening, no change in Adhesion (T.935 Section 312)
- Resistance to “bleeding” – no less than level 6 according to ASTM D-868 and ASTM D-969
- Radiation resistance – 1,200 hours in Q-Pannel with UVA-340 lamp in 8-hour light cycles at O60 temperature and 4 hours at O50 temperature , (tested by ASTM D-4587-91) –
- Gloss loss : 4%
- Viscosity – Room temperature 0.5-1.0 Pa.sec (HAAKE) 110-120 Krebs in 200 innings per minute after manual mixing 2 minutes (T.935 Section 302), After dilution 10% in the thinner – 85-90 Krebs. After 10 days it is stored at 42ºC – the position will increase to 5 krebs.
- Rigidity – 3 Dg< (Ericsson)
- Abrasion – 120 microns – 200 cycles (Gardner) ASTM, American standard ASTM D4060
- Dry film thickness 200 microns, weight loss – 2 g per 500 cycles (device – up to 2.5 g licensed loss) exfoliation strength – minimum 1 kg per square cm.
- Heat resistance up to 70 °C unchanged in features and deformation.
- Recommended layer thickness –50-100 microns dry.
- Flas hpoint – 25OC
Spray paint for Aluminum
Aluminum frames paint
Contains:
- Fillers
- Solvents.
- Resins, pigments.
- Adhesion enhancers.
- Additives.
Shade:
- In every shade of each catalog
Gloss:
- silk , (T.I.935 Section 309).
Drying to the touch:
- 10-15 minutes depending on the temperature of the environment.
- Drying time on the wheel – (T.I.935 Section 304 Repair No. 2) – up to 45 minutes
Spray paint for Aluminum
Aluminum frames paint
Drying between layers:
- 20 minutes, Final: 3-4 hours (depending on the ambient temperature)
Application methods:
- Aerosol spray in splash.
Preparation of area:
- Thorough cleaning dust, fat, dirt, it is recommended to rinse with an Degreezer AA that evaporates after cleaning and leaves a clean and dry area.
Usage instructions:
- After preparing the area, remove the aerosol lid and shake well until you hear the sound of the marbles that help mix. Spray a thin, uniform layer on the surface. If required, spray another layer 10-20 minutes later on a dry layer of paint. Wait about 20 minutes to dry.
Packaging:
- 0.4 liter spray container.
Spray paint for Aluminum
Aluminum frames paint
Storage:
- In a cool, shady place at room temperature.
- Keep lids tightly closed.
Shelf life:
- 12 months in the original packaging.
Cleaning Tools and dirt created:
- Synthetic diluter 18-D immediately after painting.
Safety:
- Not edible, out of reach of children.
- Flammable, away from heats, fire and sparks.
- Ensure proper ventilation during application.
- Wear goggles, solidarity gloves, protective clothing.
- In case of injury , seek medical attention immediately.
Spray paint for Aluminum
Aluminum frames paint
Caution:
- Do not mix with materials not recommended by us.
- Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening.
- Recommended in heats not exceeding 30 degrees and humidity of up to 50%.
- Avoid contact with the skin and eyes, causing dryness and irritation of the skin.
- In contact, rinse with plenty of running water and seek medical attention.
- Pressure tank, empty before tossing.
- Do not throw into the fire – may explode.
Quality review:
- In our factory laboratories in accordance with specifications
- ISO 9001-2015
User’s Attention:
- This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Names of consultants/professional instructors can be obtained by telephone. Read product MSDS safety instructions before starting work with it. Manufactured by Denver Colors & Coatings Israel Ltd., 80100 Sderot, 80100, certified by the Standards Institution of Israel in accordance with ISO 9001-2015 standardsן ISO 9001-2015Spray paint for Aluminum
Aluminum frames paint
- For more information about Denber Paints and Denber Projects, please contact us by phone and/or to the company’s websites:
- company profile English also
- For more details please refer to the Denber website also
- For our Facebook page click here also
- To the Facebook page of the CEO of Denber also
- For more projects click here also
- To the article: Sealer for stone and concrete and marble also
- To the article: Thermal insulation in nanotechnology also
- article: Thermal insulation Thermosil 200 energy saving in green construction also
- Related article: Thermal insulation, floor coating also
- To the article: Thermal insulation in nanotechnology company Denber also
- Fire resistance of houses, hardwood and parquet floors, decks also
- Swelling paints for steel protection against fire – Fire retardant paint also
- Epoxy floor coating in casting and painting also
- Crystal epoxy resin for tables also
- To the article Sealing also
- The complete article on the sealing materials for roofs and walls also
- Sealing the floor of the balcony, terrace from rain also
- Mold, how to remove mold correctly and how to fight mold also
- “Sick” buildings – Antibacterial paints Bacterinoll/ Tutgum Bacterinol also
- Paint for aircraft Denbergloss Jets also
- Asphaltflex execution specification – Denber Paints also
- Denbergloss grainy car paint also
- Denbergloss Clear also
- Varnish for wood. How to choose the right varnish for wood also
- Crystal epoxy for tables from Denber also
- Paint for swimming pools, epoxy Epoxyden Dengal, performance specification also
- Color specification of quadrant helmets also
- For a free consultation, call Denber – Dr. Blen Evgenia – 050-3551549 / 050-3551551 also
- Need advice? Contact us by email: Denber@bezeqint.net or contact us at 08-9960794