Spray DTM Direct To Metal TutGum Universal. Denber paints

Spray DTM Direct To Metal TutGum Universal

DTM – Primer and top coat in one paint.

Tutgum universal primer and top coat – high build paint, fast drying for almost all sorts of surfaces. Chlorinated rubber fast drying, multi thickness and multi-solid, for direct painting on iron, galvanized steel and aluminum and for universal use for most infrastructure, in a fancy silk finish. Free of chromates and lead.

Spray DTM Direct To Metal TutGum Universal. www.denber-paints.co.il

DTM – Primer and top coat in one paint.

Features:

For industrial and professional use only.
A very strong adhesive capacity for iron, aluminum and galvanized steel (not shiny)
Fast and multi-thickness drying can be applied in several layers for a desired thickness for prolonged protection. Short inter layered waiting time due to the rapid drying.
Excellent inter layered connecting ability.
The chlorinated rubber prevents the combustion of the paint in welding and fire.
Prevents the development of rust in iron and oxidation in galvanized steel.
Resistant to heat and cold and extreme marine conditions in salty seawater and fresh water.
Flexible and strong.
Easy to apply in spraying.
Decorative and serves as a final finishing layer. Primer and top coat in same paint.
Rigid, scratch resistant and shocks.

Uses:

Paint all types of metals as well as wood and walls.
To paint marking circuits on the pillars of an electric company.
For painting and marking power poles and lighting.
As a temporary element for steel before welding and cutting.
For painting in areas saturated with heat and fire risk.
As a layer of basic color and a quick drying leaf for general use.
For painting metal iron sheets and galvanized corrugated tin and aluminum products.
For painting machines in the industry.

DTM – Primer and top coat in one paint.

Technical data:

Theoretical coverage capacity – 1 liter per 15-20 square meters
Practical consumption per layer of 100 microns – 150 ml of paint per square meter for 100 microns of dry layer (minimum required).
Recommended number of layers – 1-2
% solid in volume – 60% (T.I.785 Part 17).
Color pigment content – 45% (T.I. 785 Part 19)
Adhesion – Criss cross cut “0” (T.I.P. 785 Part 27 Film 50 mic 7 drying days)
Flexibility – 1 mm (sheen) meets israeli standard 935 section 307.
Grinding – up to 50 microns (T.I.785 Part 15 – up to 60 mcg)
Density – 1.1-1.4 gm\cm3
Water immersion resistance – no bubbles, No softening, no change in Adhesion, (T.I.935 Section 312)
Resistance to “bleeding” – no less than level 6 according to ASTM D-868 and ASTM D-969
Radiation resistance – 1,200 hours in Q-Pannel with UVA-340 lamp in 8-hour light cycles at O60 temperature and 4 hours at O50 temperature, (Tested by ASTM D-4587-91) – Lightning loss : 4%
Resistance to solvents and fuels – Durable according to ASTM D-2792-93
Viscosity –Room temperature 3.0-3.5 Pa.sec (HAAKE) 110-120 Krebs in 200 rounds per minute after manual mixing of 2 minutes (T.I.935 Section 302), after diluting 10% in the thinner – 85-90 Krebs. After 10 days stored at 42 degrees Celsius – The position will increase to 5 Krebs.
Rigidity – 3 Dg< (Ericsson)
Abrasion – 120 microns – 250 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 g per 500 cycles (device – up to 2.5 g authorized loss)
Exfoliation strength – minimum 5 kg per square meter.
Heat resistance up to 70°C unchanged in features and deformation.
Recommended layer thickness –150-180 microns wet.
Flash point – 25oC

DTM – Primer and top coat in one paint.

Contains:

Chlorinated rubber with synthetic alkyd.
Fillers.
Pigments.
Adhesion enhancers.
Special flex materials.
Solvents.
Additives.
Gas.

Hue:

Every shade from every catalog.

Gloss:

silk , (T.I.935 Section 309).

Drying to the touch:

10-15 minutes depending on the temperature of the environment. Drying time on the wheel – (T.I.935 Section 304 Repair No. 2) – up to 45 minutes

Drying between layers:

20 minutes, Final: 3-4 hours (depending on the ambient temperature)

DTM – Primer and top coat in one paint.

Application methods:

Brushing, rolling, spraying in a spray gun or airless, electrostatic spraying.

Preparation of the area:

Thorough cleaning dust, fat, dirt, it is recommended to rinse with Degreezer Z to remove fats if any, rinsing with fresh water and waiting to dry, to ensure cleanliness of the area before painting.
In steel rust stains remove in st-2 mechanical polishing if the entire area is in rusty and peeling condition, SA-2.5 sand cleaning should be performed.

Packaging:

400 cc Aerosol.

Storage:

In a cool, shady place at room temperature.

Shelf life:

12 months in the original packaging.

DTM – Primer and top coat in one paint.

Cleaning tools:

Thinner 18-D immediately after painting.

Safety:

Not edible, out of reach of children.
Flammable, away from heats, fire and sparks.
Ensure proper ventilation during application.
Wear goggles, solidarity gloves, protective clothing.
In case of injury , seek medical attention immediately.
Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening.
Recommended in heats not exceeding 30 degrees and humidity of up to 50%.

Caution:

Do not mix with materials not recommended by us.
Do not paint with high environmental heat and it is recommended to paint onion only and late morning and early evening. Recommended in heats not exceeding 30 degrees and humidity of up to 50%.
Avoid contact with the skin and eyes, causing dryness and irritation of the skin.
In contact, rinse with plenty of running water and seek medical attention.
Aerosol Spray is a pressure tank, it must be emptied of gas before being thrown in the trash. It should not be thrown into the fire. There is a risk of exploding.

Quality audit:

In our factory laboratories in accordance with iso 9001-2015 specifications.

DTM – Primer and top coat in one paint.

For user attention:

This technical specification is for general non-binding information only. The product is a professional product for professionals only who have already acquired previous experience in its implementation. This specification does not serve as a substitute for advice/training by an authorized consultant/guide. It is mandatory to apply to a small area for match testing first before applying large areas. The content of this specification changes over time and updates are entered, and updated versions must be requested. Names of consultants/professional instructors can be obtained by telephone. Read product MSDS safety instructions before starting work with it. Manufactured by Denber paints & Coatings Israel Ltd., 80100 Sderot, 80100, certified by the Standards Institution of Israel in accordance with ISO 9001-2015 standards.

Spray DTM Direct To Metal TutGum Universal