Rust Converter

Rust Converter

Chemical rust converter

Chemical rust converter, which attacks the rust and converts it chemically to plastic with neutral PH acidity. For direct use on rusty iron metals for converting the rust as basic coat before primer coat. Prevents develop of rust again.

Properties:

  • Chemically rust converter.
  • Fast maintenance when starts rust to stop it and prevent development.
  • Servesas the foundationbasic paintandsavestheneed ofsand blasting ormechanicalrust removal.
  • Durable in high moisture environment conditions and in alkali and acid liquids.
  • Offering a superior adhesion to iron rusty metals.
  • Easy to apply, quickly drying.
  • Ready to repaint/recoating again on the same day or after 12 hours.
  • High coverage.
  • Durable in fuels including aviation fuel.

Applications:

  • For applying on light rusty metals to convert it before painting.
  • For surface preparation before painting where sand blasting is not possible or only partially possible.
  • For requirements of partial preparing surface with easy rust residue.

Technical data:

  • Coverage – 1 liter to 2 sqm. on smooth surface.
  • Recommended layer thickness – 1 layer of 500 mic.
  • Flexibility – 1 mm (Sheen)
  • Elongation – > 10%
  • Density – 1.4 gm/cm3
  • Viscosity – 20,000 cPs (Brookfild)
  • Adhesion power – 5 kg/cm2
  • Erosion-120 microns film – 680 cycles (Gardner) ASTM

Contains:

  • Tannic acid.
  • Acrylic emulsion.
  • Rust converters components.
  • Penetration materials.
  • Additives

Color:

  • Milky white.

Gloss:

Touch dry time:

  • 6-8 hours, Final drying: 24 hours. Final hardness 7 days.

Drying between layers:

  • 6-24 hours according environment temp..

Application methods:

  • Brush, roller.

Thinning:

  • Not aloud

Surface preparation:

  • A thorough cleaning needed from dirt, dust and loose paints and heavy rust/

Primer:

  • This product itself.

Top color:

  • Any iron metal primer.

Packaging:

  • 1, 5, 18 liters.

Storage:

  • In cool and shaded room in room temp. with proper ventilation.
  • Keep lids tightly closed.

Shelf life:

  • 12 months in original package.

Tools cleaning:

Quality control:

  • In factory laboratories according to specifications.
  • COA and COC certificate.
  • ISO 9001-2015

Safety precautions:

  • Inedible, keep away from the reach of children.
  • While applying, good air ventilation is important. In case there is not enough air, use ventilation according to the ventilation table.
  • Wear protective glasses, gloves and suits.
  • Avoid direct contact of the paint and/or thinner with the eyes and skin. In case of contact, immediately wash thoroughly with water.
  • In case of an injury immediately get doctors assistance.
  • Read the safety instructions on the labels.
  • See M.S.D.S

Warnings:

  • Don’t mix the product with materials which were not recommended by us.
  • Don’t apply if the temperature is under +7°C .
  • Don’t apply if humidity is over 80%
  • When applying with Airless, do not aim it at anybody a direct hit could be fatal at pressures over 150 atm.
  • Read thoroughly the technical data of the product listed in this section; confirm that everything is understood completely, for clarification contacts our tech. department.
  • All information that is listed in this content is a recommendation merely and cannot be applied in the court of law.
  • The costumer must test & check that this product is compatible with his equipment and needs.
  • The information listed in this section is according to the laboratory conditions (temperature, humidity etc.) which the products were tested.
  • The recommendations listed do not hold any responsibility for this product.
  • Theoretical and actual coverage area are different concepts, the actual coverage is affected by the required thickness of the layers, required number of layers, painting conditions including the amount of paint which spread in the air before touching the surface.
  • The information listed in this section is based on experience and accumulating data, Denber inc., has the right to change the information listed at any time.
  • Paints that have been in stagnation or exposed to air more than needed could have their qualities changed.

Clarifications:

  • Storage room temperature 15°C to 25°C.
  • Over Spray: An effect which occurs in the spraying of paints application. A type of “dust” is created by dry gases of the air, which causing the paint particles to fall dry on the surface (hereafter the “effect”). The impact of this “effect” becomes stronger due to over pressure and heat, (most sprayers have a lever to control the pressure) To avoid the negative impact 0f the “effect”, the pressure of the spraying should be lowered to the necessary minimum!. Another possibility is to increase the amount of the thinner in the mixture which would cause the paint particles to fall wetter on the surface.

An additional recommended possibility, to avoid this “effect”, is to add a retarder to the mixture which increases the duration period of the painting application , avoiding the paint to  dry up, and enabling it to reach the surface wetter, Thus a better painted smooth  layer is formed.

  • Pot Life : The working time which is possible to paint a mixture of two components, A+B (or more) without spoiling the qualities of the paint or disqualifying the paint as “out of use”.
  • Spray: It is possible to spray with a sprayer that has a container holding the paint that sprays it with air pressure.
  • Airless: a device with a piston which compresses the air for spraying paints. The pressure might be high (over 100atm.) Don’t aim it at anyone
  • Surface preparations: the level of cleanness is determined by international standards. Surface preparations, including cleansing sand blasting, is important & critical factor in achieving an optimal result for painting adhesion on a certain surface. These standards are equally compared to the standards of the Swiss SA, the German-Din the U.S SSPC SP For each standard in any level there are indicators, for sale,  in order to make visual comparison between the cleansing of the surface and the indicator.

 

Quality inspection:

  • Prior to the painting on large surfaces it is important to test the product on a small area, to be sure that the paint is compatible with the level of satisfactory.
  • Laboratory testing was made according to the standards institution specifications.
  • This “Data sheet” given as noncommittal information, the product above recommended for professional painting specialists. This information is not a substitute to personal guidance.
  • You must read the MSDS safety instructions before you start working with the product.

Safety instructions and transportation risk levels:

* According to UVV 24 (VGB 32) standards.

  • It is recommended to cover containers and tubes which have flammable substances from ‘A’ group, level: 1, 2, 3, and from group ‘B’.

 

Hardener Thinner Base
Fuel transportation
V b F A 11
Vehicle transportations of dangerous substances
In GGVE\RID train 3N 31c
Secret material sea transportation CLASS 3.3 CLASS 3.3 CLASS 3.3
  UN no 1866 UN no 1866 UN no 1866

Rust Converter