Synthetic Paint ТТЕ-529, general colors.

Synthetic Paint ТТЕ-529, general colors.

TT-E-529 ALKYD SEMI-GLOSS ENAMEL

APPLICATION & REDUCTION: Intrepid TT-E-529 Enamels can be applied by conventional or airless spray application. For spraying, thin up to 10% or as needed with Xylene. For brushing, use as is or with minimum thinning. Type II should be thinned with Intrepid T0123 Intrepid

Synthetic Paint ТТЕ-529, general colors. www.denber-paints.co.il

Synthetic Paint ТТЕ-529, general colors. www.denber-paints.co.il

Synthetic Paint ТТЕ-529, general colors.

TT-E-529 ALKYD SEMI-GLOSS ENAMEL

This specification covers one type of an air drying, semigloss, alkyd enamel for use on primed exterior and interior metal and wood surfaces. This specification is canceled. Superseded by A-A-2962.

PRODUCT: A semi-gloss, alkyd enamel formulated for interior
and exterior metal and wood surfaces. This coating
is primarily used as a medium air dry finish coat on
equipment. Also available in Type II, Baking Enamel
and Type III Aerosol Cans for touch-up.
PROPERTIES: COLORS…………………………. Fed Std. 595B
GRIND……………………………. Not Under 6
SPECULAR GLOSS……………….. 15 – 25 @60 Deg
VISCOSITY…………………………. 67 – 77 KU
DRYING TIME-AT 75 DEGREES F:
SET-TO-TOUCH…………………… Within 2 Hours
DRY HARD………………………. Within 8 Hours
FULL HARDNESS…………………. Within 72 Hours

Synthetic Paint ТТЕ-529, general colors.

TT-E-529 ALKYD SEMI-GLOSS ENAMEL

TYPE II:
BAKE HARD: 30 MINS @ 300 Degrees Fahrenheit
ADVANTAGES: (1). Interior / Exterior Use
(2). Semi-Gloss Finish
(3). Meets TT-E-529
(4). Full Color Range, 595 Colors
(5). Fast Production Time.
USES: (1). Steel
(2). Machinery
(3). Tanks
(4). Wood
(5). Equipment
(6). Towers
APPLICATION & REDUCTION:
Intrepid TT-E-529 Enamels can be applied by conventional or
airless spray application. For spraying, thin up to 10% or as
needed with Xylene. For brushing, use as is or with minimum
thinning. Type II should be thinned with Intrepid T0123 Intrepid
Baking Enamel Reducer at 10%-15% by volume for spray application.
Spray one tack coat followed by one full wet coat. For Type II,
allow part to air dry for 30-45 minutes at room temperature.
Pre-heat oven to 300 Degrees Fahrenheit, place part in oven and
bake for 30 minutes.

Synthetic Paint ТТЕ-529, general colors.

TT-E-529 ALKYD SEMI-GLOSS ENAMEL

SURFACE PREPARATION:
Surface must be clean, dry and free of all contamination before
application. Prime per specification instructions.
STEEL:
Surface must be clean and free of all oil, grease and foreign
material. Badly rusted or pitted steel should be cleaned by
commercial sandblasting and primed the same day.
PRECAUTIONS:
Contents are FLAMMABLE.
Keep away from heat and open flame.
KEEP OUT OF THE REACH OF CHILDREN.
Do not take internally.
Avoid breathing vapor or mist.
Do not use in tank or pit without proper protection.
Read Material Safety Data Sheet before use of this product.

Synthetic Paint ТТЕ-529, general colors.

TT-E-529 ALKYD SEMI-GLOSS ENAMEL