Solar collectors Denberust black
Black anti-rust paint absorbs heat, stores heat, is rich in soot for painting solar collectors.
Solar collectors color matte black and store brown

Solar collectors Denberust black www.denber-paints.co.il
DENBERUST BLACK’ SUN LIGHT RECEIVER ZINC PHOSPHATE SYNTHETIC ANTI-RUST PRIMER AND TOP COAT FOR SOLAR SYSTEMS
For painting solar collectors and solar energy systems. Used as a foundation and top. The shade and the low gloss allow maximum absorption of the sun’s heat.

Solar collectors Denberust black www.denber-paints.co.il
Characteristics:
- Maximum heat absorption capacity due to the shade and deep matte shine.
- Excellent resistance to outdoor conditions.
- Excellent protection against rust.
- Excellent adhesion to steel, black iron and galvanized sheet metal.
- Easy to apply and dries quickly.
- Quick drying, ready for repainting and/or coating on the same day and even within a few hours in the summer if necessary.
- High coverage area.
- Contains zinc phosphate that creates durability and resistance to the development of rust in the long term.
Uses:
- Painting solar collectors in different solar systems.
Black anti-rust paint absorbs heat, stores heat, is rich in soot for painting solar collectors
Technical data:
- Theoretical coverage – 1 liter for about 20 square meters.
- Recommended layer thickness – 25-35 microns.
- Recommended number of layers – 2
- % solids by volume – 55% < (T.I. 785 part 17).
- % solids by weight – 65% <
- Flexibility – 1 mm (sheen)
- Grinding minutes – up to 20 microns (Ti 785 part 15 – up to 60 microns)
- Density – 1.15-1.35 gm/cm 3
- Resistance to immersion in water – no bubbles, no softening, no change in adhesion
- Viscosity – 1.2-1.4 sec (HAAKE) 78-92 kerbs at 200 revolutions per minute after manual mixing for 2 minutes (TI 935 section 302), after diluting 10% with thinner – 65 kerbs. After 10 days storage at 42 degrees Celsius – Proximity will increase up to 5 Krebs.
- Adhesion – cris cross cut “0” test (T.I. 785 part 27 film 50 micron 7 drying days)
- Stiffness – 3 Dg < (Ericsson)
- Abrasion – 120 microns – 1050 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 grams per 500 cycles (standard – up to 2.5 grams authorized loss).
- Salt chamber – 120 hours (ASTM B-117) without rust spots.
Containing:
- synthetic resin.
- Melanins, soot pigments.
- Special plasticizers.
- zinc phosphate.
- Solvents, additives.
- Sictives
Color:
- black.
Gloss:
- Matt.
Touch drying :
- 1-2 hours
- Drying for treatment – 10 hours, drying between layers – 8 hours, final drying – 16 hours.
Application methods:
- Brushing, rolling, spraying.
Dilution:
- Brushing/rolling – 10% mineral turpentine
- Spraying – 30%-20 thinner D18 pressure 3-4 atm
- Airless – 0-5% thinner D18, “0.018” nozzle – for a thin layer. “0.021” nozzle for a thick layer.
- Immersion – 100% diluted D18
Area preparation:
- Chemical – degreasing with degreaser M, rust removal with degreaser 3000. f
- Mechanical – sand cleaning to grade 2.5 SA/ steel brush ST-3 and
- Thorough cleaning of dust, grease, dirt and loose paint. and
Packing:
- 2.5 liters, 5 liters, 18 liters. and
This technical specification is for non-binding general information only. and
Produced by Denber Paints and Coatings Israel Ltd. , and
For the full specification: Black Denberust collectors for solar collectors