Epoxyden Ship Abrasive Antislip

Ship antislip epoxy denber colors www.denber-paints.co.il

Rough anti-slip abrasive – mixed/transparent epoxy top paint, two-component, fine/medium rough decorative, for painting deck floors and anti-slip railings.

EPOXYDEN SHIP ABRASIV –  TOP COAT  TWO COMPONENT  ABRSION RESIST FOR DECK FLOORS AND BANISTERS ANTI SLIP COATING IN SHIPS

Colored or transparent top paint with a fine/medium roughness (optional) for painting on Epoxy Ship Primer or on old epoxy castings for renewal and anti-slip coating, extra strong. Creates a strong rough decorative protective layer with high adhesion to epoxy primer for floors, railings, deck parts that tend to get wet and pose a slipping hazard.

Epoxyden Ship antislip www.denber-paints.co.il

Characteristics:

• Prevents slipping even when the floor is wet.
• Top paint for floors with mechanical strength and high adhesion to Epoxyd Ship Flour Primer.
• In many shades, creates a proper protection for the floor for durability in unusual conditions.
• Resistant to alkaline solutions and mixed acids and abnormal humidity conditions.
• powerful
• Easy to apply and repaint and dries quickly.
• Resistant to polluted industrial water.
• Resistant to fuels and oils including jet fuel
• and resistant to detergents.
• and resistant to scratches and blows.
• Suitable for painting industrial floors on which light equipment and carts move.
• Covers the floor with a thin and even decorative layer in shades with a subtle roughness.
• Excellent mechanical strength and resistance to wear under light loads.
• Resistant to momentary heat up to 200 degrees and more prolonged heat up to 150 degrees.
• Easy to repair at low cost.
• High coverage area.
• High electrical insulation.

Anti-skid epoxy paint in a thin layer with fine/medium roughness

uses:

• Epoxy for painting floors and stairs and railings in upper deck areas that are usually wet and present a slip hazard.
• As a top for walking floors inside the ship to prevent slipping while the ship is moving.
• For painting floors for pedestrians in galleries, shops, clubs, offices, sleeping compartments in trains and vessels, etc.

Technical data:

• Consumption per square meter – 1 liter per 4 square meters for a layer of 175 dry microns per layer.
• Flexibility – 1 mm (sheen) film 120 microns.
• Density – for matte gloss – 1.6-1.7 gm/cm ³  , (1475 (ASTM D
• Amount of solids – 65% Part A by weight 68%, Part B by volume 52% (ASTM-D-2369)
• Mixing ratio A:B – 2.5:1 by volume.
• Stiffness – >10 Dg (Ericsson)
• Abrasion – 120 microns – 3560 cycles (Gardner) ASTM
• Recommended layer thickness – 250 microns wet, 175 microns dry.
• Recommended number of layers – 1
• Pot life (working time from the moment of mixing A with B) – 4 hours.

Containing:

• Polyamide epoxy resin. and
• Melanes, quartz, pigments. and
• Polyamide keys. and
• Solvents. and
• additives. and

Color:

• Transparent and any color from the RAL catalog. and

Gloss:

• Glossy, silky, matte and
• Matt. 10-30% (ASTM D 523) and

This technical specification is for non-binding general information only. and

Manufactured by Denber Paints and Coatings Israel Ltd. , PO Box 690 Sderot, 80100, certified by the Israeli Standards Institute in accordance with the  ISO 9001-2015 standard and

For the full specification:  anti-slip epoxy epoxy-ship abrasive and

Epoxy and polyurethane floor is done by the experts of Denver and

Recommendations:  Magrek – the color of ships