Seals vertical piping by a spill

Fluid for repairing leaking pipes

A high-performance, flexible, transparent liquid membrane coating for sealing the interior of vertical pipes of gutters, sewers and water.

For piping inside concrete walls and columns and piping that cannot be easily replaced or repaired due to lack of access.

A transparent liquid pipe surface coating of hybrid polyurethane polysiloxane, produced with a unique, one-component moisture polymerizing technology, penetrates and seals holes and cracks in leaky vertical pipes. Adheres well to all types of piping and coats them. Excellent coverage of small holes and cracks and stops leaks.

Characteristics:

• One component is easy to use.
• Easy to apply by pouring into a tube.
• Thin and penetrates and seals every hole and crack in the pipe.
• Polymerizes from air humidity and does not require the use of hardener.
• Completely transparent.
• flexible.
• Adhesion to all types of piping.
• Perfect seal from water.

Uses:

• For sealing gutter pipes.
• For sealing sewer pipes.
• for sealing water pipes.

Technical data:

• Dry to the touch – after about three hours in the summer.
• Viscosity mPs – 600.
• Shore D – 75 difficulties.
• Elongation – 250%.
• Resistance to tearing – 50 N/mm
• Maximum layer thickness – 1 mm
• Flexibility – 1 mm (sheen)
• Adhesion – above the strength of the concrete.
• Density – 0.9-1.0 gm/cm ³
• Stiffness – >10 Dg (Ericsson).
• Abrasion – 120 microns – 4200 cycles (Gardner) ASTM.
• Recommended layer thickness – 0.5 mm to 1 mm
• % solids by volume – 50%
• Recommended number of layers – 1-3

Fluid for repairing leaking pipes

containing:

• A special hybrid polysiloxane polyol.
• Prepolymer.
• Moisture sensitive keys.
• Melanes.
• catalysts
• Mineral turpentine.
• additives.

Color:

• Clear.

Drying between layers :

• 6-24 hours, final – 24 hours, final difficulty – 3 days.
• In the summer, dehydration is possible within two hours, a contact test is required.

Application methods:

• Clogging the drain hole with a plumber’s balloon/cloth/any other way (not polyurethane foam).
• Ejaculate until the tube is full.
• Waiting 30 minutes and emptying.
• Collecting the material into hermetically sealed packaging ( the packaging must be placed upside down to prevent air infiltration ) and repeating the process after 6-24 hours.
• For small cracks, 24 hours for final drying and water injection for inspection.
• The material will continue to harden for another two days.
• If there is still liquid, wait for the water to dry in the pipes, close the outlet again and fill again with the material.

User manual:

• Open the container carefully, pour into the pipe up to above the level of the leak or flood the entire pipe. Drying within 6-24 hours, maximum strength after 3 days.
• If the problem was a thin crack, one coating may be enough.
• After 24 hours of drying, for large holes or a crack larger than 1 mm, the operation must be repeated again and again until complete sealing.

Dilution:

• Not for dilution. Ready to use.

Preparing the surface for sealing:

• The areas to be sealed should be well polished, free of any dust, grease and dirt and completely dry. It is recommended to go over the sealing areas with a cloth soaked in acetone to ensure their cleanliness from grease and dirt and to improve adhesion.

Packing:

• 1 liter.
• 5 liters.
• 18 liter packages only for use on the same day and by order.

This technical specification is for  non-binding general information only. and

Produced by Denver Paints and Coatings Israel Ltd. , and

For the full specification:  vertical pipeline sealer in spillage