Denbergloss 7 electrical insulation

Denbergloss 7 electrical insulation

Two-component paint/varnish for electrical insulation

UV resistant polyurethane paint for electrical insulation

A hard, multi-solid , two-component top polyurethane paint , UV resistant for interior and exterior painting, for resistance to particularly harsh conditions including direct exposure to the sun and rains, especially suitable as a top paint for electrical insulation of electrical systems exposed to water.

DENBERGLOSS 7 (2:1) – POLYURETHANE TWO COMPONENT TOP COAT for electrical insulation

Denbergloss 7 electrical insulationwww.denber-paints.co.il

Characteristics:

Excellent electrical insulation.
Smooth and hard finish.
Flexible and hard at the same time.
Very washable and repels dust and dirt.
High hardness, suitable for outdoor conditions such as electrical cabinets and electrical poles and street lighting.
Excellent adhesion to the infrastructure.
Resistant to scratches and mechanical damage.
Easy to apply.
UV resistant, chemical resistant.
Heat and cold resistance.
Very high gloss or other on demand, durable for many years.
quick drying.
Does not contain cadmium, lead, chromates.

Uses:

As a top layer for electrical insulation of systems that may come into contact with water or high humidity and transmit electricity that can endanger human life and/or cause a short circuit.
For painting accessories and parts that produce/transmit electricity and mobile/permanent ground equipment that produces electricity.
For painting street lighting poles and peripheral lighting, for painting lighting lanterns, for painting electrical cabinets and branches, for painting electrical poles, for painting generators, for painting electrical cabinets, etc.

UV resistant polyurethane paint for electrical insulation

Technical data:

Part A – can be mixed by hand easily and after 5 minutes you will get a uniform and smooth solution.
Part B – will be transparent and clear.
Storage durability – 24 hours at 57 ⁰ without separation and spoilage,
Theoretical coverage – 1 liter per 10-15 square meters.
Recommended layer thickness 40-50 dry microns.
Recommended wet layer thickness – 80-100 microns.
Recommended number of layers -2
Flexibility – 1 mm (sheen)
Density – 1.1-1.3 gm/cm ³ (varnish 0.9 colors up to 1.3)
Stiffness –>10 Dg (Ericsson)
Abrasion – 120 microns – 3600 cycles (Gardner) ASTM
Base to hard ratio – 2:1
Durability time of diluted paint in the package – 6 hours (viscosity increase no more than 6 seconds from original viscosity)
Shine at 60 ⁰ – shiny 80% <, silk 15-45%, matte 5% >
Pot life = working time from the moment of mixing B+A – 6> hours.
Resistance to distilled water 24 hours – without loss of adhesion or corrosion one hour after removal from the liquid.
Hydrocarbon resistance – no loss of adhesion one hour after removal from the liquid.
For resistance in oil 1250 24 hours at ^O C 121- without loss of adhesion 4 hours after removal from the liquid.
For resistance in hydraulic oil 24 hours at ^O C 66 – without loss of adhesion 4 hours after removal from the liquid
Resistance to jet fuel – 7 days at room temperature – no loss of adhesion 4 hours after removal from the liquid
Heat resistance – ^O C121 for 60 minutes. No tone changes up to delta E =1.
Humidity chamber – 30 days in 100% humidity at a temperature of ^O C49 without loss of adhesion or damage to the film one hour after removal from the liquid
Salt cell – without the appearance of corrosion.
Thermal market – without loss of adhesion.
% solids by volume – glossy < 52%, matte and silky < 45%, marking and transparent colors < 35%.
Electrical insulation (dielectric strength) at a temperature of 18-22 degrees 30 kilovolts per mm – passes.
Dielectric strength for voltage breakdown for a dry layer 25 microns – KV/mm 150 (ASTM-D-149)

Packing:

3.4+1.6 = 5 liters.

This technical specification is for non-binding general information only. and

For the full specification: Denbergloss 7 UV resistant electrical insulation