TUTGUM POOL PAINT

TUTGUM POOL PAINT

Tutgum sealing paint for pools/reservoirs

Seals pores and prevents water from passing through

Penetrates, fills pores and seals

TUTGUM POOL PAINT www.denber-paints.co.il

TUTGUM POOL PAINT www.denber-paints.co.il

Characteristics:

  • Ready to use. For painting on epoxy primer primer for concrete and fiber and wash primer primer for aluminum.
  • Flexible and strong, decorative in several shades in addition to standard blue.
  • Excellent adhesion to the corresponding primary colors.
  • Easy to apply with a brush/roller/spray.
  • Dries quickly.
  • Ability to resist standing water and under pressure created by deep water load.
  • Excellent sealer.
  • Flexible and does not crack in summer temperature changes between day and night in direct exposure to the sun.
  • Can be applied in any weather except rainy days.
  • Resistant to chlorine except for the fading of the pigment tone caused by its attack due to excessive concentration of chlorine in the water.
  • Non-toxic and does not emit toxins, suitable for human contact and non-toxic when drinking pool water. Can be painted over with blue epoxy approved for drinking water by the Israeli Standards Institute.

Uses:

  • For painting and sealing concrete water reservoirs for irrigation.
  • For sealing fish ponds of all kinds and water reservoirs.

Technical data:

  • Approximate consumption – 1 liter per 5 square meters. In two layers.
  • Flexibility – 1 mm (sheen) passes the test of Israeli standard 935 section 307.
  • Grinding minutes – up to 50 microns (Ti 785 part 15 – up to 60 microns).
  • Density – 1.10-1.35 gm/cm 3  .
  • Resistance to immersion in water – no bubbles, no softening, no change in adhesion, (TI 935 section 312).
  • Resistance to “sweating” (bleeding) – not less than level 6 according to ASTM D-868 and ASTM D-969 Resistance to solvents and fuels – resistant according to ASTM D-2792-93.
  • Viscosity -0.5-1.5 sec (HAAKE), 12,000 CPS (Brookfield)
  • Stiffness – >10 Dg (Ericsson).
  • Tensile strength – 75 kg per square meter.
  • Abrasion – 120 microns – 1050 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 grams per 500 cycles (standard – up to 5 grams authorized loss).
  • Heat resistance up to 70 degrees Celsius without change in properties and deformation.
  • Recommended number of layers – 2-3.
  • UV resistance – 12 months when exposed to the sun.
  • Elongation before weathering – up to 250%
  • Temperature resistance –  O C60+ to    O C60-
  • Resistance to water pressure – 4 atmospheres

Penetrates, fills pores and seals

Color:

  • Standard light blue, ocean blue

Glass:

  • Matte – silk.

Dilution:

  • Brushing – 5-10% thinner D-32
  • Spraying – 10-30% thinner D-32 pressure 3-4 atm.
  • Airless – 5-10% thinner D-32 pressure 5-6 atm nozzle “0.015
  • In winter when it is cold, you can use D-18 thinner which dries faster.

Area preparation and recommendation for application:

  • Thorough cleaning of dust, grease, dirt, sand cleaning and mechanical grinding until perfect cleaning is recommended.
  • Clean and dry conditions must be observed to obtain correct results.
  • After cleaning – careful vacuuming of all the dust with an industrial vacuum cleaner.
  • For concrete and fiberglass pools – 2 layers of primer “Epoxydan Fluor Primer” by spray or roller, minimal waiting time between layers (drying to the touch without fingerprint marks)
  • If putty repairs are to be made – epoxy putty should be used after the first primer layer, and within 24 hours paint the second primer layer.

Packing:

  • 2.5 liters, 5 liters, 18 liters.

Produced by Denber Paints and Coatings Israel Ltd

See Epoxy pool paint  Epoxy dangle swimming pool paint