Clear epoxy for 3D images

Clear epoxy for 3D images www.denber-paints.co.il

A leveling  transparent top epoxy coating  , two-component multi-thickness, 100% solids, strong and thick wear-resistant,  for coating floors  on which pictures have been drawn or pasted, including three-dimensional pictures. Creates a smooth and level surface, easy to clean.

EPOXYDEN FLOOR HB, CLEAR, 100% SOLIDS SOLVENTLESS EPOXY SELF LEVELING FOR COATING PICTURES ON FLOORS BY POURING.

Characteristics:

• Provides a smooth transparent surface that protects the image on the floor, on which you can walk.
• Levels itself and creates a smooth and even surface.
• Smooth and hard finish for decorative concrete floors.
• Thick, high hardness, abrasion resistant, scratch resistant.
• Top coating for 3D images.
• It is easy to apply in casting as it has self-leveling ability.
• Resistant to various chemicals, oils and fuels, solvents, resistant to acids and bases in low concentrations – see resistance table.
• Heat and cold resistance. Resistant to unusual humidity conditions in fresh, distilled, salt water.
• Not resistant to direct exposure to the sun. Dunbargloss Clear should be watched.
• Does not contain cadmium, lead, chromates.

Uses:

• Top transparent coating for photos.

Multi-thickness epoxy fluor clear for photos

Technical data:

• Part A – cloudy transparent, can be easily mixed by hand and after 5 minutes you will get a uniform and smooth solution.
• Part B – will be transparent and clear.
• Storage durability – 24 hours at 570 without separation and spoilage,
• Coverage – 1 liter per 1 square meter in a layer of 1 mm.
• Recommended minimum layer thickness – 300 microns.
• Recommended maximum layer thickness – no limit.
• Flexibility – 4 mm (sheen)
• Density – 1.1-1.3 gm/cm3
• Average viscosity A + B – 12,000 cPs (Brookfield)
• Bending strength – 30 newtons/mm2,
• Impact strength – 1.8 joules/mm2
• Stiffness – >10 Dg (Ericsson)
• Abrasion – 120 micron – 4500 cycles (Gardner) ASTM
• Ratio of base to hardener – in a transparent shade – 2:1 by weight. or 1:06 by volume.
• Pot life = working time from the moment of mixing B+A to packing 5 liters – 20-30 minutes.
• Resistance to distilled water 24 hours – without loss of adhesion or corrosion one hour after removal from the liquid.
• Hydrocarbon resistance – no loss of adhesion one hour after removal from the liquid.
• and oil resistance 1250 24 hours at OC 121 – without loss of adhesion 4 hours after removal from the liquid.
• and hydraulic oil resistance 24 hours at OC 66 – no loss of adhesion 4 hours after removal from the liquid
• Resistance to jet fuel – 7 days at room temperature – no loss of adhesion 4 hours after removal from the liquid
• Heat resistance – O C121 for 60 minutes. No tone changes up to delta E =1.
• Humidity chamber – 30 days in 100% humidity at a temperature of OC49 without loss of adhesion or damage to the film one hour after removal from the liquid
• Salt cell – 3000 hours without the appearance of corrosion.
• Thermal market – no loss of adhesion.
• % solids – 100%.
• Adhesion to steel – 210 kg/cm2, adhesion to concrete – more than the tearing strength of the concrete.

Packing:

• Transparent: 1+0.5 kg = 1.5 kg, 3.4+1.6 kg = 5 kg, 10+5 kg = 15 kg

This technical specification is for non-binding general information only. and
manufactured by Denber Paints and Coatings Israel Ltd. , and

For the full specification:  transparent epoxy for 3D images