EPOXYDEN PRIMER ELECTROSTATIC PAINT

EPOXYDEN PRIMER ELECTROSTATIC PAINT

Epoxy epoxyden electrostatic primer for oven or air drying

Air-dry epoxy primer or bake in the oven at 150 degrees for 30 minutes

Two-component anticorrosive electrostatic for metal, aluminum for a continuous production line.

EPOXYDEN PRIMER ELECTROSTATIC TWO COMPONENT FOR METAL PARTS AND ALUMINUM. FOR STOVING OR AIR DRY.

The paint creates a strong base layer with high adhesion to the infrastructure, suitable for ferrous steels and aerospace parts made of aluminum alloys that have undergone appropriate surface preparation according to the American standard in all its stages.

EPOXYDEN PRIMER ELECTROSTATIC PAINT www.denber-paints.co.il

Characteristics:

Electrostatic paint for frontal spraying of formal elements and for receiving an enveloping color coating from all sides.
A primer with mechanical strength and high adhesion to the infrastructure.
Creates proper protection from rust and corrosion for the painted part for durability in unusual conditions.
Base for painting metal parts such as steel, aluminum and aviation aluminum alloys.
Protects against oxidation or rust in Brazilian metals.
Resistant to alkaline solutions and mixed acids and abnormal humidity conditions.
powerful
Easy to apply and repaint and dries quickly in an oven at 150 degrees
Suitable for painting industrial and aviation elements.
Suitable for painting bicycle frames and others in an automatic continuous production line.
And suitable for spraying with a paint turbine, airless and spray gun.
Coat the painted part with a thin and uniform layer

Uses:

For painting formal metal items in an automatic electrostatic production and painting line.
As a foundation for various metal parts in industry and for aviation in the fields of aviation and space.

Technical data:

Coverage – 1 liter per 10-15 square meters in a layer of 50 dry microns minimum.
Flexibility – 1 mm (sheen)
Density – part A 1.3-1.5 gm/cm ³ , part B 0.85-0.95 gm/cm ³ (1475 (ASTM D
Viscosity – part A about 90 kerbs part 2 about 25 kerbs (10% + )
Stiffness – >10 Dg (Ericsson)
Flash point: Part A – 27 degrees Celsius, Part B – 166 degrees.
Amount of solids – part A by weight 75%, part B by volume 52% (ASTM-D-2369)
Abrasion – 120 microns – 2560 cycles (Gardner) ASTM
Recommended layer thickness – 75-100 wet microns. 50 microns dry (minimum values)
Recommended number of layers – 2 -1
Hard drying time – in an oven at 150 degrees for 30 minutes

Air-dry epoxy primer or bake in the oven at 150 degrees for 30 minutes

Containing:

Melamine epoxy resin. and
Melanins, pigments. and
Solvents. and
additives. and
makes it difficult and

Color:

red-brown
gray.

Gloss:

Matt

Drying between layers:

Wait at least 30 minutes for cooling after leaving the oven. Final: 4 hours.

Application methods:

Electrostatic spraying with paint turbine. and
Electrostatic spraying with an electrostatic paint gun. and

Dilution:

Dilute 6/100 D.
10-25% by volume as needed. If an “orange peel” appearance is obtained, the dosage can be increased to 35%
Spraying with an electrostatic pistol – 10-25%

Area preparation:

Thorough cleaning of rust, dust, grease, dirt and loose paint. and
Aluminum and aluminum alloys Exposed/new aviation aluminum – treatment for the preparation of the burning area and passivation according to the standards: MIL-C-5541 MIL-C-81706
Very large bodies – removing paint with approved paint removers and washing with water to neutralize. Sharpening/blasting soft balls for roughness and thorough cleaning. Thorough washing and drying. and

Packing:

5 liters, 18 liters. and

This technical specification is for non-binding general information only. and

Manufactured by Denver Paints and Coatings Israel Ltd. , P.O. Box 690 Sderot, and

For full specifications: Epoxy epoxyden electrostatic primer for roasting