TUTGUM ANTISTATIC ACRYLIC BLACK

TUTGUM ANTISTATIC ACRYLIC BLACK

Antistatic black electrically conductive tutgum acrylic paint.

Static electricity grounding and shielding of all types of plastic electronics enclosures.

Antistatic Tutgum, fast drying antistatic solvent black paint

Black antistatic paint conducts electricity to the shield and conducts static electricity to the ground. Fast drying anticorrosives, for plastic cases of all types and metals. Resistance 10 ⁴ -10 ⁸ Ohm or less as required.

TUTGUM ANTISTATIC – electrically conductive antistatic and anticorrosive fast drying black paint.

TUTGUM ANTISTATIC BLACK www.denber-paints.co.il

Characteristics:

Electrically conductive paint for shielding and conducting static electricity to the ground.
quick drying.
Anti-static.
Excellent adhesion to the infrastructure.
Easy to apply by spraying, roller.
Resistant to weather conditions.
One component.
Hard with a smooth finish.

Antistatic Tutgum, fast drying antistatic solvent black paint

Uses:

For painting plastic cases and others.
For painting work surfaces and walls.
Fast drying anticorrosive antistatic primer layer.
Suitable as an antistatic element for painting metals.
For painting data and communication cables for shielding.

Technical data:

Consumption – 200-250 grams per square meter.
% solids – about 48% (T.I. 785 part 17).
Pigment content in the color – 65% (T.I. 785 part 19)
Flexibility – 1 mm (sheen) passes the test of Israeli standard 935 section 307.
Grinding minutes – up to 50 microns (Ti 785 part 15 – up to 60 microns)
Density – 1.45-1.6 gm/cm ³
Resistance to immersion in water – no bubbles, no softening, no change in adhesion, (TI 935 section 312)
Bleeding resistance – no less than level 6 according to ASTM D-868 and ASTM D-969
For resistance to solvents and fuels – resistant according to ASTM D-2792-93
Viscosity – at room temperature: 1.5-2.5 sec (HAAKE) 78-92 kerbs at 200 revolutions per minute after manual mixing for 2 minutes (TI 935 section 302), after diluting 10% with thinner – 65 kerbs. After 10 days store in 42 degrees Celsius – the proximity will increase up to 5 Krebs.
Stiffness – < 10 Dg (Ericsson)
Abrasion – 120 microns – 1800 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 grams per 500 cycles (standard – up to 2.5 grams authorized loss)
Peeling strength – minimum 5 kg per square meter.
Heat resistance up to 70 degrees Celsius without change in properties and deformation.
Recommended layer thickness – 250-200 wet microns.
Recommended number of layers for foundation – 1-2 depending on need.

Antistatic Tutgum, fast drying antistatic solvent black paint

containing:

Resins.
Melanins, anticorrosive pigments.
Special plasticizers.
Deep penetration materials.
Solvents, additives.

Color:

black.

Gloss:

Matt up to 18%, (Tai 935 section 309).

Touch drying :

15-25 minutes. Drying time in a wheel – (Ti 935 Section 304 Amendment No. 2) – up to 45 minutes

Application methods:

Mix lightly, dilute as needed and spread or spray.

Dilution:

The paint is ready to use without dilution. If thick, it can be thinned a little with thinner D-18 for spraying or D-32 for applying with a brush.
If the lid is left open, you can add 21-D thinner and mix well until you get a thin but not too thin mixture that is convenient to use, to prevent the graphite from settling.

Area preparation:

Thorough cleaning of dust, grease, dirt, washing with degreaser Z or degreaser MC is recommended to remove grease if any, to ensure the cleanliness of the surface before painting.