Tutgum Bazaq red/gray/white fast drying primer

Tutgum Bazaq red/gray/white fast drying primer

Quick-drying primer for black iron against rust, can be painted in cumulative thick layers to obtain a desired thickness

Very fast drying metal primer against rust

Totagum Bezeq primer red gray white fast drying www.denber.net
Totagum Bezeq primer red gray white fast drying www.denber.net

Anti-rust anticorrosive metal primer with chlorinated rubber and rapid alkyd, extremely fast drying, for ferrous metals, containing zinc phosphate and red pigment against rust  IRON OXIDE

TUTGUM BAZAK  – anticorrosive fast drying primer Paint for iron metals.

Characteristics:

  • Rust protective primer for ferrous metals.
  • Extremely fast drying.
  • Flexible and strong.
  • Excellent adhesion to the infrastructure.
  • Easy to apply with brush, spray, roller.

Uses:

  • First anticorrosive primer layer for all types of metals.
  • Suitable as a primer for painting aluminum parts, galvanized sheet metal, iron, etc.
  • For painting steel constructions, gates, fences, bars, custards, machines, stairs and steel railings, etc.

Technical data:

  • Consumption – 200-250 grams per square meter.
  • % solids – about 48% (T.I. 785 part 17).
  • Pigment content in the color – 65% (T.I. 785 part 19)
  • Flexibility – 1 mm (sheen) passes the test of Israeli standard 935 section 307.
  • Grinding minutes – up to 50 microns (Ti 785 part 15 – up to 60 microns)
  • Density – 1.45-1.6 gm/cm 3
  • Resistance to immersion in water – no bubbles, no softening, no change in adhesion, (TI 935 section 312)
  • Bleeding resistance – no less than level 6 according to ASTM D-868 and ASTM D-969
  • and resistance to solvents and fuels – resistant according to ASTM D-2792-93
  • Viscosity – at room temperature: 1.5-2.5 sec (HAAKE) 78-92 kerbs at 200 revolutions per minute after manual mixing for 2 minutes (TI 935 section 302), after diluting 10% with thinner – 65 kerbs. After 10 days store in 42 degrees Celsius – the proximity will increase up to 5 Krebs.
  • Stiffness – < 10 Dg (Ericsson)
  • Abrasion – 120 microns – 1800 cycles (Gardner) ASTM, American standard ASTM D4060 dry film thickness 200 microns, weight loss – 2 grams per 500 cycles (standard – up to 2.5 grams authorized loss)
  • Peeling strength – minimum 5 kg per square meter.
  • Heat resistance up to 70 degrees Celsius without change in properties and deformation.
  • Recommended layer thickness – 250-200 wet microns.
  • Recommended number of layers for foundation – 1-2

Very fast drying metal primer against rust

Containing:

  • Chlorinated rubber and special resin.
  • Melanins, anticorrosive pigments.
  • Special plasticizers.
  • Deep penetration materials.
  • Solvents, additives.
  • zinc phosphate.

Closs:

  • Red/brown, gray, white.

Gloss:

  • Mate up to 18%, (Tai 935 section 309).

Touch drying :

  • 15-25 minutes. Drying time in a wheel – (Ti 935 Section 304 Amendment No. 2) – up to 45 minutes

Dilution:

  • The paint is ready to use without dilution. If thick, it can be thinned a little with thinner D-18 for spraying or D-32 for applying with a brush.
  • If the lid is left open, you can add 21-D thinner and mix well until you get a thin but not too thin mixture that is convenient to use.

Area preparation:

  • Thorough cleaning of dust, grease, dirt, washing with degreaser Z or degreaser MC is recommended to remove grease if any, to ensure the cleanliness of the surface before painting.

Packing:

  • 1 liter, 5 liters, 18 liters.

This technical specification is for non-binding general information only. and

Produced by Denber Paints and Coatings Israel Ltd. , and

For the full specification:  Tutgum Bazaq primer red gray white fast drying