Epoxy antistatic primer black for floors

Epoxy antistatic primer black for floors

Primer that penetrates concrete, electrically conductive black, for an antistatic floor coating system

Epoxy antistatic primer for floors  Epoxydan Fluor antistatic primer  paint-epoxy – charcoal black antistatic epoxy primer for concrete floors under the copper strips. (1:1) two-component, penetrating, creates a base layer, electrically conductive preparation for thick antistatic coating in shades of floors and in a thin layer antistatic top coating for walls. To prevent static electricity by grounding it to the ground through the electrically conductive layer. For electronics laboratories and test and control rooms with sensitive and precise electronic equipment, clean rooms, rooms with precise measuring equipment and others.

EPOXYDEN FLOOR ANTISTATIC PRIMER BLACK CONDUCTIVE CONCRETE FLOOR PRIMER UNDER THE COPPER STRIPS  

Characteristics:

• High-quality electrical conduction, which brings static electricity to copper strips that are above and connected to grounding. Conducts electricity well and works even without the copper strips.
• Penetrates concrete (small molecular size) and builds a strong foundation with “roots”.
• Creates an electrically conductive infrastructure ready for coating.
• Suitable for application with a roller.
• Can be recoated after gluing the copper strips to protect them from contact with the spreader bar during casting.
• Seals the Purim in the floor and prevents the emission of gases that create bubbles during casting.
• Resistant to acids and alkalis according to the attached table.
• Resistant to standing water and also to those mixed with industrial and chemical waste for a long time.
• and resistant to fuels and oils. Resistant to detergents and industrial chemicals.
• and resistant to blows, scratches and heavy loads.
• Very washable and repels dust and dirt.
• Heat and cold resistance.

uses:

• Electrically conductive foundation layer for concrete floors and walls for an antistatic coating system.

Primer that penetrates concrete, electrically conductive black, for an antistatic floor coating system

Technical data:

• Theoretical coverage – 1 liter per 10 square meters.
• Density – 1.1-1.2 gm/cm3
• Pot life – lifespan after mixing A with B – 7 hours at 20 degrees.
• Recommended film thickness – 100-250 microns dry, 200-500 microns wet.
• Recommended number of layers – 1-2 and another layer above the copper strips after gluing them.
• Base to hard ratio – 1:1
• Flash point: base – 38 degrees.
• Adhesion to concrete – more than the strength of the concrete
• Tahina minutes – Mat 5 > Hagman
• Barak at 600 -, matte >5%
• % solids – 55%.

Electrical data:

• Option – surface resistance – ASTM F 150-89 – for every 10 cm resistance less than 10 kilo ohms.
• Resistance to earth – without copper strips – as above
• Option – ground resistance with copper strips – 1 mm thick – 60-425 ohms.
• Standard antistatic resistance – 0.01-100 mega ohm. (10 kilo ohms to 100 mega ohms)

 variety:

• black

 packing:

• 2.5+2.5 = 5 liters. 9+9= 18 liters. and

 Static electricity in average values ​​produced by a person walking on the floor:

• Insulated shoes – 60-150 volts. and
• Leather shoes – 12-50 volts. and
• Special antistatic plastic shoes – 10-30 volts. and

Discharge time for a voltage of 500 volts of static electricity generated by walking with the above shoes:

• Insulated shoes – 3-8 seconds f
• Leather shoes – 0.25-2.5 seconds. and
• Special antistatic plastic shoes – 0.05-1 seconds and

This technical specification is for non-binding general information only. and

Manufactured by Denver Paints and Coatings Israel Ltd. , P.O. Box 690 Sderot, 80100, certified by the Israeli Standards Institute in accordance with the ISO 9001-2015 standard

For the full specification:  Epoxy antistatic primer for floors and