THERMOSEAL POLYFLEX ROOF SEALING

Insulation coating heat/cold and seals from rain

Two-component polyurethane membrane coating 100% solids 100% elongation, which provides  perfect sealing from rain and high-quality thermal insulation from heat and cold  based on nanotechnology of hollow ceramics, and also creates   significant acoustic insulation . Very thick and powerful for covering all kinds of roofs. Resistant to hot temperatures and deep freezing and unlimited defrosting. For use in hot and cold countries. Also suitable for driving and parking a light vehicle  . Suitable for thermal insulation of hot roofs in industry and roofs of cooling and freezing rooms.

THERMOSEAL POLYFLEX – FOR ROOF SEALING AND THERMO ISOLATION  

A new technology for roofing, especially strong, for sealing and high-quality thermal insulation, wear-resistant with a unique molecular structure, which completely seals against moisture and allows elongation and contraction according to extreme temperature changes. Strengthens the existing infrastructure and gives a smooth and very strong layer resistant to erosion and suitable for regular use including use as a public balcony, parking lot, etc. Seals and bridges across capillary cracks. Fills gaps and seals perfectly. Provides excellent thermal insulation that, with the right thickness, prevents heat/cold from passing to the floor below. Resistant to temperatures of   ^OC 50 – up  to ^OC 120 +

Insulation coating heat/cold and seals from rain

Characteristics:

• A perfect sealer from water, repels moisture and prevents penetration of concrete in concrete or tile roofs.
• Thermal and acoustic insulator. Significantly reduces rain noise on the roof.
• UV resistant
• The thermal insulation creates significant energy savings for heating/cooling the floor under the coated roof. The coating is in a white shade that repels heat.
• Creates a quiet and pleasant atmosphere in the rooms under the roof. Allows climate control, contributes to improving the quality of sleep.
• Flexible, extends by  at least 100%  and bridges capillary cracks.
• Strengthens any cement, bituminous and tin infrastructure.
• Excellent adhesion to the infrastructure.
• The strength of its adhesion allows a multi-thickness coating in one thick casting from 0.5 mm to 10 cm.
• Significantly and immediately stops water penetration.
• Easy to apply and dries quickly.
• 100% solids  without diluents and without smell .
• Flexible and shock absorber and hard and violent mechanical blows, suitable as a shock absorber around pipes penetrating the roof, drainage channels. and
• Ready for repainting and/or coating on the same day in the summer. and
• The coated surface is smooth with a fine roughness and very washable. and
• Roughness aggregate can be added during casting to prevent slipping in roofs used as a balcony, but washing will be more difficult. and

uses:

• For sealing and thermal insulation for all types of roofs, including roofs used for light vehicle parking. and
• For coating concrete roofs, asbestos, shingles, iskurit, on existing tar coating and bituminous sheets. and
• Suitable for public balconies open to pedestrians. and
• For coating walls and ceilings in cold rooms to improve thermal insulation and washability and prevent condensation. and

Insulation coating heat/cold and seals from rain

Technical data:

• Theoretical coverage for roofs – 1 liter per 0.25 square meters on a smooth roof with a thickness of 4 mm. and
  for perfect thermal insulation. 1 liter per 1 square meter for perfect sealing and partial thermal insulation. f
• Minimum layer thickness is recommended for waterproofing Iskurit roofs – 2 layers of 750 microns and
• Mixing ratio by volume part A: B – 4:1 
• POT LIFE Life time after mixing A + B – 20 minutes f
• Elongation – 100% <
• Light reflection – 75%.
• solids – 100%

To the old site: http://www.denber-paints.co.il

This technical specification is for  non-binding general information only. 

For full specifications:  Roof sealing and Thermosil Polyplex roof thermal insulation

Lowering temperature from 49 degrees to 35 degrees. At the Nesher Ramla power plant gas turbine.