Polyplex two-component gum expansion seam filling
Asphalt and concrete flexible filling polyurethane rubber for expansion joints resistant to heavy loads and blows
For filling and coating seams in concrete floors in industry 37% or 100% elongation.
Polyplex two-component gum expansion seam filling www.denber-paints.co.il
Filler of expansion seams Polyplex two-component mastic for expansion seams-heavy loads – thick and powerful polyurethane for flexible filling and sealing of expansion seams in concrete, thin for casting or thick for application , for resistance to pressures and severe vibrations. Excellent durability in a corrosive, aggressive environment, high abrasion resistance, for use in the heavy, chemical, aviation and marine industries. 37% elongation or 100% elongation , two 100% solid components. Suitable for driving light and heavy vehicles, forklifts, chemical resistance, freight carts, truck boxes, container floors, etc. Produced in a ratio of 3:1 for casting and in a ratio of 2:1 for application. Flexible and perfectly seals expansion seams and prevents liquids from passing through the seam and leaks to the floor below.
POLYFLEX MASTIC FOR CONCRETE SEAMS (STICHES SOLVENT FREE VIBRATION AND ABRASION RESTRAIN, CHEMICAL RESIST, FOR INDUSTRIAL CONCRETE FLOORS, ELONGATION 37% OR 100%
Characteristics:
- Flexible stretches by at least 37% or 100%
- Prevents cracking in expansion joints in concrete where all contraction and expansion forces drain.
- bridges capillary cracks.
- Resistant to constant shocks and vibrations from industrial production machinery.
- A perfect sealer from water, repels moisture and prevents penetration into concrete.
- Resistant to abrasion and chemicals, resistant to standing water and industrial wastewater.
- Resistant to fuels, oils and harsh detergents.
- Returns to its original shape after each press without any deformation.
- Resistant to boiling water and heat up to 120 degrees for short periods and 80 degrees Celsius for very long periods.
- Excellent adhesion to the infrastructure.
- The strength of its adhesion allows a multi-thickness coating in one thick casting from 0.5 mm to 20 cm and filling large expansion seams and/or fractures that are formed on both sides of the seam from blows from transporting surfaces and driving forklifts, this in one application or casting.
- Significantly and immediately stops water penetration.
- Easy to apply and dries quickly.
- 100% solids without diluents and odorless.
- Flexible and shock absorber and hard and violent mechanical blows and suitable as a shock absorber around drainage channels.
- Ready for re-casting the same day and even within a few hours in the summer.
- Does not contain any thinners and can be used in places with minimal ventilation.
For filling and coating seams in concrete floors in industry 37% or 100% elongation
Technical data:
- Consumption: 100% solids, amount of liters according to the amount for casting. 3 mm thickness per square meter = 3 liters per square meter.
- Flexibility – 1 mm (sheen).
- Elongation – 100% < for most requirements, or 37% for particularly unusual loads (for example – for forklifts of 6 tons and more).
- Density – 1.2-1.3 gm/cm3
- Mixing ratio – 3:1 for pouring, 2:1 thick for spreading
- Recommended layer thickness – no thickness limit but not less than 200 microns.
- Recommended number of layers – with one thick layer or unlimited additional layers in the future, only light polishing is required to prepare an area to improve adhesion between the layers.
- Working time from mixing A with B – 60 minutes at 20 degrees Celsius.
- Ripening time for use – 24 hours
- And final ripening time – 3-7 days.
Color:
- Standard gray or any shade as ordered (minimum 250 liters per shade).
Recommendations: Dizengoff Center
- This technical specification is for non-binding general information only.
- For the full specification: Polyflex two-component mastic expansion seam filling
- To the old site: http://www.denber-paints.co.il
English
עברית
Русский